+2
Downloaded file will be available after import in the {{cadTool}} tool library.
| Objednací číslo | 5358450 |
| ISO katalogové ID | SDR100031E0NW |
| ANSI katalogové ID | SDR100031E0NW |
| Grade | WDN00U |
| Cutting Edges per Insert | 1 |
| [LI] Insert Length | 22.23 mm |
| [LI] Insert Length | .875 in |
| [W] Insert Width | 9.53 mm |
| [W] Insert Width | .375 in |
| [Rε] Corner Radius | 0.8 mm |
| [Rε] Corner Radius | .0312 in |
| Average Chip Thickness [HM] | 0.02 mm |
| Average Chip Thickness [HM] | .0008 in |
Karbidy
WDN00U
An ultra-fine grained polycrystalline diamond (PCD) tip brazed onto a carbide substrate. Designed for general-purpose turning of primarily non-ferrous materials. Applied over a wide range of continuous to interrupted cuts where superior surface finish is needed. Use on low to medium silicon content aluminum alloys, non-metallics, copper, brass, and zinc-based alloys. The ultra-fine grained diamond particle size enables superior surface finishes while ensuring the best mechanical shock resistance of any PCD cutting tool.
Vytvořit řešení pro výpočet posuvů a rychlosti
Po vytvoření řešení stačí vybrat ikonu Posuvy & Rychlosti a náš systém poskytne doporučení. Informace můžete upravit přidáním zařízení a specifikací nebo provést úpravy pomocí posuvníků.
| ae/D1 = | 0,2 | 0,3 | 0,4 |
| Koeficient fz | 1,5 | 1,3 | 1,0 |
| Koeficient vc | 1,3 | 1,2 | 1,1 |
| Geometrie břitových destiček | Programovaný posuv na zub (fz) jako % poměr radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
| 10% | 20% | 30% | 40% | 50–100% | ||||||||||||
| SDR… | 0,08 | 0,17 | 0,33 | 0,06 | 0,13 | 0,25 | 0,06 | 0,11 | 0,22 | 0,05 | 0,10 | 0,20 | 0,05 | 0,10 | 0,20 | SDR… |
| EDR… | 0,08 | 0,17 | 0,33 | 0,06 | 0,13 | 0,25 | 0,06 | 0,11 | 0,22 | 0,05 | 0,10 | 0,20 | 0,05 | 0,10 | 0,20 | EDR… |
| Lehké obrábění | Všeobecné použití | Těžké obrábění |
| ae/D1 = | 0,2 | 0,3 | 0,4 |
| Koeficient fz | 1,5 | 1,3 | 1,0 |
| Koeficient vc | 1,3 | 1,2 | 1,1 |
| ae/D1 = | 0.2 | 0.3 | 0.4 |
| fz-Factor | 1.5 | 1.3 | 1.0 |
| vc-Factor | 1.3 | 1.2 | 1.1 |
| Lehké obrábění | Všeobecné použití | Těžké obrábění |
| Geometrie břitových destiček | Programovaný posuv na zub (fz) jako % poměr radiální hloubky řezu (ae) | Geometrie břitových destiček | ||||||||||||||
| 10% | 20% | 30% | 40% | 50–100% | ||||||||||||
| SDR… | .003 | .007 | .011 | .003 | .005 | .008 | .002 | .004 | .007 | .002 | .004 | .006 | .002 | .004 | .006 | SDR… |
| EDR… | .003 | .007 | .011 | .003 | .005 | .008 | .002 | .004 | .007 | .002 | .004 | .006 | .002 | .004 | .006 | EDR… |
| ae/D1 = | 0.2 | 0.3 | 0.4 |
| fz-Factor | 1.5 | 1.3 | 1.0 |
| vc-Factor | 1.3 | 1.2 | 1.1 |
| ae/D1 = | 0,2 | 0,3 | 0,4 |
| Koeficient fz | 1,5 | 1,3 | 1,0 |
| Koeficient vc | 1,3 | 1,2 | 1,1 |
| ae/D1 = | 0,2 | 0,3 | 0,4 |
| Koeficient fz | 1,5 | 1,3 | 1,0 |
| Koeficient vc | 1,3 | 1,2 | 1,1 |
| Materiálová skupina | WDN00U | |||
| P | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| 4 | – | – | – | |
| 5 | – | – | – | |
| 6 | – | – | – | |
| M | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| K | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| N | 1–2 | 910 | 1980 | 4880 |
| 3 | 460 | 610 | 760 | |
| S | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| 4 | – | – | – | |
| H | 1 | – | – | – |
| ae/D1 = | 0.2 | 0.3 | 0.4 |
| fz-Factor | 1.5 | 1.3 | 1.0 |
| vc-Factor | 1.3 | 1.2 | 1.1 |
| Materiálová skupina | WDN00U | |||
| P | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| 4 | – | – | – | |
| 5 | – | – | – | |
| 6 | – | – | – | |
| M | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| K | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| N | 1–2 | 3000 | 6500 | 16000 |
| 3 | 1500 | 2000 | 2500 | |
| S | 1 | – | – | – |
| 2 | – | – | – | |
| 3 | – | – | – | |
| 4 | – | – | – | |
| H | 1 | – | – | – |
| ae/D1 = | 0.2 | 0.3 | 0.4 |
| fz-Factor | 1.5 | 1.3 | 1.0 |
| vc-Factor | 1.3 | 1.2 | 1.1 |
| Materiálová skupina | Lehké obrábění | Všeobecné použití | Těžké obrábění | |||
| Geometrie | Sorta | Geometrie | Sorta | Geometrie | Sorta | |
| P1–P2 | – | – | – | – | – | – |
| P3–P4 | – | – | – | – | – | – |
| P5–P6 | – | – | – | – | – | – |
| M1–M2 | – | – | – | – | – | – |
| M3 | – | – | – | – | – | – |
| K1–K2 | – | – | – | – | – | – |
| K3 | – | – | – | – | – | – |
| N1–N2 | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U |
| N3 | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U |
| S1–S2 | – | – | – | – | – | – |
| S3 | – | – | – | – | – | – |
| S4 | – | – | – | – | – | – |
| H1 | – | – | – | – | – | – |
CAD Drawings Models
Can’t find the file type you’re looking for?
Product data
I have read and accepted the Terms & Conditions of use
Katalogové číslo ISO
Katalogové číslo ANSI
to find similar products.Please select a file to download
Models
. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.
Minimum quantity should be
| SAP Material Number | Katalogové číslo ISO | Karbid |
|---|
You are about to leave the Solution building process.
Are you sure you want to leave?