Welcome
Please confirm your preferences
Update Preferences

Product Suggestions

Product Family suggestions

Contact a WIDIA Expert

Customer Support

Find customer support centers around the globe.

Quick Order
Item(s) successfully added to cart
View Cart

    KM Indexable Torque and Power

    For Indexable Insert End Mill with KM Quick-Change Tooling

    These calculations are based upon theoretical values and are only intended for planning purposes. Actual results will vary. No responsibility from Kennametal is assumed.

    Conversion of Workpiece Material Rockwell (Optional):
    Metric
    Inch

    Conversion of Workpiece Material Rockwell (Optional)

    Skip this step if you already know the Brinell hardness number(HB)
    Characteristics of Workpiece Materials

    Characteristics of Workpiece Materials

    HB
    PSI N/mm 2
    Ultimate Strength shown for generic steel. Please enter the actual value of your workpiece material if available, for better accuracy You may look up this info through websites such as www.matweb.com
    End Mill Nomenclature

    End Mill Nomenclature

    in.mm.
    in. mm.
    in. mm.

    Machining Conditions

    sfm m/min
    in.(DOC) mm (DOC)
    in.(WOC) mm(WOC)
    in. IPT (chip load) mm
    Most Common Workpiece MaterialsCm at W/D ratios:
    W/D < = 0.660.66 < W/D < 1.0W/D = 1.0
    Aluminum alloys1.01.051.1
    Carbon and alloy steels1.01.151.3
    Cast irons1.01.151.3
    Titanium alloys1.01.201.4
    Stainless steel, High-temperature alloys2.02.152.3
    MillingDepth of cutFeed per toothCw
    Category(min-max), in.(min-max), in.&nbsp;
    Light0.020-0.1000.003-0.0061.1
    Medium0.100-0.2000.006-0.0101.2
    Heavy duty0.200-0.4000.010-0.0201.3
       
    Direct Belt Drive.9
    Back Gear Drive.75
    Geared Head Drive.7-.8
    Oil - Hydraulic Drive.6-.9

    Safe Operating Conditions

    lbN
    lbN
    ft lbNm
    ft lbNm

    Calculated Machining Conditions

    RPM
    (IPM)(no productivity formula)mm/min
    in (chip load at the cut) mm/min
    (IPM)(with productivity formula)mm/min
    in.3/min MRRcm3/min3
    in.2mm2

    Calculated Required Power

    lbf should not exceed Ft maxN
    ft-lb should not exceed TpNm

    Machining Power

    HPckW
    hpkW
    You are about to add to your My Solutions page. Do you want to proceed?
    Select the destination where you want to move to.
    New Folder
      • Applied Filters:
      • Clear All

    A folder with the name already exists.

    Please enter a valid name
    product-image
    Please adjust the following properties from

    ISO Catalog Number

    ANSI Catalog Number

    to find similar products.

    The following files are available

    Please select a file to download

    Models

    I have read and accepted the Terms & Conditions of use

    Can’t find the file type you’re looking for?

    You should be logged to see your dashboard information
    Session expired due to inactivity, please login again
    The product/s () you were trying to add to the cart is/are not available, please contact customer service
    item(s) successfully added to the cart
    View Cart

    . Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.

    Minimum quantity should be

    SAP Material NumberISO Catalog NumberGrade  

    You are about to leave the Solution building process.

    Are you sure you want to leave?