Produkt ähnlich wie:
Wendeschneidplatten PCD • SuperFeed • Planfräser • SDR
Wendeschneidplatten
Material Nummer100014895
Auswahlhilfe für Wendeschneidplatten
Werkstoffgruppe | Leichte Bearbeitung | Allgemeine Anwendung | Schruppbearbeitung | |||
Geometrie | Sorte | Geometrie | Sorte | Geometrie | Sorte | |
P1–P2 | – | – | – | – | – | – |
P3–P4 | – | – | – | – | – | – |
P5–P6 | – | – | – | – | – | – |
M1–M2 | – | – | – | – | – | – |
M3 | – | – | – | – | – | – |
K1–K2 | – | – | – | – | – | – |
K3 | – | – | – | – | – | – |
N1–N2 | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U |
N3 | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U | SDR…/EDR… | WDN00U |
S1–S2 | – | – | – | – | – | – |
S3 | – | – | – | – | – | – |
S4 | – | – | – | – | – | – |
H1 | – | – | – | – | – | – |
Empfohlene Startwerte für Vorschübe [mm]
ae/D1 = | 0,2 | 0,3 | 0,4 |
fz-Faktor | 1,5 | 1,3 | 1,0 |
vc-Faktor | 1,3 | 1,2 | 1,1 |
Schneidkörper- Geometrie | Programmierter Vorschub pro Zahn (fz) | Schneidkörper- Geometrie | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
SDR… | 0,08 | 0,17 | 0,33 | 0,06 | 0,13 | 0,25 | 0,06 | 0,11 | 0,22 | 0,05 | 0,10 | 0,20 | 0,05 | 0,10 | 0,20 | SDR… |
EDR… | 0,08 | 0,17 | 0,33 | 0,06 | 0,13 | 0,25 | 0,06 | 0,11 | 0,22 | 0,05 | 0,10 | 0,20 | 0,05 | 0,10 | 0,20 | EDR… |
Leichte Bearbeitung | Allgemeine Anwendung | Schruppbearbeitung |
ae/D1 = | 0,2 | 0,3 | 0,4 |
fz-Faktor | 1,5 | 1,3 | 1,0 |
vc-Faktor | 1,3 | 1,2 | 1,1 |
Recommended Starting Feeds [IPT]
ae/D1 = | 0.2 | 0.3 | 0.4 |
fz-Factor | 1.5 | 1.3 | 1.0 |
vc-Factor | 1.3 | 1.2 | 1.1 |
Leichte Bearbeitung | Allgemeine Anwendung | Schruppbearbeitung |
Schneidkörper- Geometrie | Programmierter Vorschub pro Zahn (fz) | Schneidkörper- Geometrie | ||||||||||||||
10% | 20% | 30% | 40% | 50–100% | ||||||||||||
SDR… | .003 | .007 | .011 | .003 | .005 | .008 | .002 | .004 | .007 | .002 | .004 | .006 | .002 | .004 | .006 | SDR… |
EDR… | .003 | .007 | .011 | .003 | .005 | .008 | .002 | .004 | .007 | .002 | .004 | .006 | .002 | .004 | .006 | EDR… |
ae/D1 = | 0.2 | 0.3 | 0.4 |
fz-Factor | 1.5 | 1.3 | 1.0 |
vc-Factor | 1.3 | 1.2 | 1.1 |
Empfohlene Start-Schnittgeschwindigkeiten [m/min]
ae/D1 = | 0,2 | 0,3 | 0,4 |
fz-Faktor | 1,5 | 1,3 | 1,0 |
vc-Faktor | 1,3 | 1,2 | 1,1 |
ae/D1 = | 0,2 | 0,3 | 0,4 |
fz-Faktor | 1,5 | 1,3 | 1,0 |
vc-Faktor | 1,3 | 1,2 | 1,1 |
Werkstoffgruppe | WDN00U | |||
P | 1 | – | – | – |
2 | – | – | – | |
3 | – | – | – | |
4 | – | – | – | |
5 | – | – | – | |
6 | – | – | – | |
M | 1 | – | – | – |
2 | – | – | – | |
3 | – | – | – | |
K | 1 | – | – | – |
2 | – | – | – | |
3 | – | – | – | |
N | 1–2 | 910 | 1980 | 4880 |
3 | 460 | 610 | 760 | |
S | 1 | – | – | – |
2 | – | – | – | |
3 | – | – | – | |
4 | – | – | – | |
H | 1 | – | – | – |
Recommended Starting Speeds [SFM]
ae/D1 = | 0.2 | 0.3 | 0.4 |
fz-Factor | 1.5 | 1.3 | 1.0 |
vc-Factor | 1.3 | 1.2 | 1.1 |
Werkstoffgruppe | WDN00U | |||
P | 1 | – | – | – |
2 | – | – | – | |
3 | – | – | – | |
4 | – | – | – | |
5 | – | – | – | |
6 | – | – | – | |
M | 1 | – | – | – |
2 | – | – | – | |
3 | – | – | – | |
K | 1 | – | – | – |
2 | – | – | – | |
3 | – | – | – | |
N | 1–2 | 3000 | 6500 | 16000 |
3 | 1500 | 2000 | 2500 | |
S | 1 | – | – | – |
2 | – | – | – | |
3 | – | – | – | |
4 | – | – | – | |
H | 1 | – | – | – |
ae/D1 = | 0.2 | 0.3 | 0.4 |
fz-Factor | 1.5 | 1.3 | 1.0 |
vc-Factor | 1.3 | 1.2 | 1.1 |