Top Cut 4 • 3 x D • SLRシャンク • メトリック

Name: Top Cut 4 • 3 x D • SLRシャンク • メトリック
SKU: 100015202
Rating: 0 (0 reviews)

TC4 • 3 x D • SLRシャンク • メトリック

特徴と利点

Tool body shipped with insert wrench

使用法と用途

Shank - Cylindrical with Flat
Drilling
Drilling: Inclined Entry
Drilling: Inclined Exit
Drilling: X-Offset
穴あけ加工：凸面
スルークーラント：径方向：スローアウェイドリル
穴あけ加工：止まり穴
Chain Drilling
Drilling: Cross-Hole Drilling
Drilling: Half-Cylindrical Drilling
Drilling: Corner Drilling 45°

TC4 • インサート選択の手引き

Material Group	Geometry	Light Machining		General Purpose		Heavy Machining
Material Group	Geometry	periphery insert	center insert	periphery insert	center insert	periphery insert	center insert
P1	V38/DU	WU25CH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
P2–P4	V34/DU	WPK10CH	WU40PH/WU20PH	WU25CH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
P5–P6	V36/DU	WU25CH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
M1–M3	V36/DU	WU25CH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
K1–K3	V34/DU	WPK10CH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
N1–N4	V36	WN10PH	WN10PH	WN10PH	WN10PH	WN10PH	WN10PH
S1–S4	V38/DU	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH

							Recommended Feed Rate per Revolution
Material Group	Geometry	Grade		Cutting Speed vc m/min			Tool Diameter	12,00 13,99 Insert Size A	14,00 18,99 Insert Size B	19,00 23,99 Insert Size C	24,00 29,99 Insert Size D
Material Group	Geometry	center	periphery	Min	Start	Max	Tool Diameter	12,00 13,99 Insert Size A	14,00 18,99 Insert Size B	19,00 23,99 Insert Size C	24,00 29,99 Insert Size D
P0	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,06–0,08	0,08–0,11	0,10–0,13	0,11–0,14
P0	–DU	WU20PH	WU20PH	90	150	200	mm/rev	–	–	0,07–0,10	0,08–0,10
P1	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,06–0,10	0,08–0,13	0,10–0,15	0,11–0,16
P1	–DU	WU20PH	WU20PH	90	150	200	mm/rev	–	–	0,07–0,11	0,08–0,11
P2	–V34	WU40PH	WU25CH	120	190	280	mm/rev	0,06–0,10	0,08–0,15	0,10–0,16	0,11–0,17
P2	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0,07–0,12	0,08–0,13
P3	–V34	WU40PH	WPK10CH	120	200	310	mm/rev	0,08–0,15	0,10–0,16	0,11–0,18	0,12–0,20
P3	–DU	WU20PH	WU20PH	90	160	220	mm/rev	–	–	0,08–0,13	0,09–0,15
P4	–V34	WU40PH	WPK10CH	120	190	310	mm/rev	0,08–0,15	0,10–0,16	0,11–0,18	0,12–0,20
P4	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0,08–0,13	0,09–0,15
P5	–V36	WU40PH	WU25CH	120	180	250	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
P5	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0,07–0,11	0,08–0,12
P6	-V36	WU40PH	WU25CH	120	160	210	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
P6	–DU	WU20PH	WU20PH	90	130	165	mm/rev	–	–	0,07–0,11	0,08–0,12
M1	-V38	WU40PH	WU40PH	120	160	240	mm/rev	0,06–0,11	0,07–0,11	0,08–0,12	0,10–0,14
M1	–DU	WU20PH	WU20PH	90	130	190	mm/rev	–	–	0,06–0,09	0,07–0,10
M2	–V38	WU40PH	WU40PH	110	140	210	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
M2	–DU	WU20PH	WU20PH	110	140	190	mm/rev	–	–	0,06–0,09	0,07–0,10
M3	-V36	WU40PH	WU40PH	100	120	200	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
M3	–DU	WU20PH	WU20PH	80	100	160	mm/rev	–	–	0,06–0,09	0,07–0,10
K1	-V34	WU25CH	WPK10CH	120	200	280	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K1	–DU	WU20PH	WU20PH	90	160	220	mm/rev	–	–	0,07–0,13	0,09–0,18
K2	–V34	WU40PH	WPK10CH	100	180	260	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K2	–DU	WU20PH	WU20PH	80	140	200	mm/rev	–	–	0,07–0,13	0,09–0,18
K3	-V34	WU40PH	WPK10CH	100	170	240	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K3	–DU	WU20PH	WU20PH	80	140	190	mm/rev	–	–	0,07–0,13	0,09–0,18
N1	-V36	WN10PH	WN10PH	250	350	500	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
N2	–V36	WN10PH	WN10PH	150	300	450	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
N3	-V36	WN10PH	WN10PH	80	120	150	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
S3	-V38	WU40PH	WU40PH	20	30	45	mm/rev	0,08–0,12	0,08–0,13	0,10–0,15	0,12–0,19
S3	–DU	WU20PH	WU20PH	20	30	40	mm/rev	–	–	0,07–0,11	0,09–0,14
S4	–V38	WU40PH	WU40PH	35	40	65	mm/rev	0,08–0,12	0,08–0,13	0,10 –0,15	0,12–0,19
S4	–DU	WU20PH	WU20PH	30	40	60	mm/rev	–	–	0,07–0,11	0,09–0,14

Material Group	Geometry	Grade		Cutting Speed vc m/min			Tool Diameter	30,00 36,99 Insert Size E	37,00 45,99 Insert Size F	46,00 56,99 Insert Size G	57,00 68,00 Insert Size H
Material Group	Geometry	center	periphery	Min	Start	Max	Tool Diameter	30,00 36,99 Insert Size E	37,00 45,99 Insert Size F	46,00 56,99 Insert Size G	57,00 68,00 Insert Size H
P0	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,13–0,16	0,15–0,18	0,16–0,23	0,17–0,24
P0	–DU	WU20PH	WU20PH	90	140	200	mm/rev	0,09–0,12	0,11–0,13	–	–
P1	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,13–0,17	0,15–0,19	0,16–0,24	0,17–0,25
P1	–DU	WU20PH	WU20PH	90	140	200	mm/rev	0,09–0,13	0,11–0,14	–	–
P2	–V34	WU40PH	WU25CH	120	190	280	mm/rev	0,13–0,20	0,15–0,21	0,16–0,28	0,17–0,30
P2	–DU	WU20PH	WU20PH	90	150	220	mm/rev	0,09–0,15	0,11–0,15	–	–
P3	–V34	WU40PH	WPK10CH	120	200	310	mm/rev	0,16–0,24	0,16–0,24	0,18–0,30	0,19–0,32
P3	–DU	WU20PH	WU20PH	90	160	250	mm/rev	0,12–0,16	0,12–0,18	–	–
P4	–V34	WU40PH	WPK10CH	120	190	310	mm/rev	0,14–0,22	0,16–0,24	0,18–0,30	0,19–0,32
P4	–DU	WU20PH	WU20PH	90	150	250	mm/rev	0,12–0,16	0,12–0,18	–	–
P5	–V36	WU40PH	WU25CH	120	180	250	mm/rev	0,13–0,18	0,15–0,20	0,16–0,28	0,17–0,30
P5	–DU	WU20PH	WU20PH	90	140	200	mm/rev	0,09–0,13	0,11–0,15	–	–
P6	-V36	WU40PH	WU25CH	120	160	210	mm/rev	0,13–0,18	0,15–0,20	0,16–0,28	0,17–0,29
P6	–DU	WU20PH	WU20PH	90	120	160	mm/rev	0,09–0,13	0,11–0,15	–	–
M1	-V38	WU40PH	WU40PH	120	160	240	mm/rev	0,12–0,17	0,14–0,21	0,16–0,23	0,16–0,24
M1	–DU	WU20PH	WU20PH	90	120	190	mm/rev	0,09–0,13	0,10–0,15	–	–
M2	–V38	WU40PH	WU40PH	110	140	210	mm/rev	0,12–0,17	0,14–0,21	0,16–0,23	0,16–0,24
M2	–DU	WU20PH	WU20PH	90	110	160	mm/rev	0,09–0,13	0,10–0,15	–	–
M3	-V36	WU40PH	WU40PH	100	120	200	mm/rev	0,12–0,17	0,14–0,21	0,16–0,23	0,16–0,24
M3	–DU	WU20PH	WU20PH	80	90	160	mm/rev	0,09–0,13	0,10–0,15	–	–
K1	-V34	WU25CH	WPK10CH	120	200	280	mm/rev	0,14–0,26	0,16–0,30	0,18–0,32	0,20–0,36
K1	–DU	WU20PH	WU20PH	90	160	220	mm/rev	0,10–0,19	0,12–0,22	–	–
K2	–V34	WU40PH	WPK10CH	100	180	260	mm/rev	0,14–0,26	0,16–0,30	0,18–0,32	0,20–0,36
K2	–DU	WU20PH	WU20PH	80	140	200	mm/rev	0,10–0,19	0,12–0,22	–	–
K3	-V34	WU40PH	WPK10CH	100	170	240	mm/rev	0,14–0,26	0,16–0,30	0,18–0,32	0,20–0,36
K3	–DU	WU20PH	WU20PH	80	130	190	mm/rev	0,10–0,19	0,12–0,22	–	–
N1	-V36	WN10PH	WN10PH	250	350	500	mm/rev	0,13–0,18	0,15–0,20	0,16–0,28	0,17–0,30
N2	–V36	WN10PH	WN10PH	150	300	450	mm/rev	0,13–0,18	0,15–0,20	0,16–0,28	0,17–0,30
N3	-V36	WN10PH	WN10PH	80	120	150	mm/rev	0,12–0,17	0,14–0,21	0,16–0,23	0,16–0,24
S3	-V38	WU40PH	WU40PH	20	30	45	mm/rev	0,14–0,21	0,16–0,24	0,18–0,26	0,20–0,30
S3	–DU	WU20PH	WU20PH	20	25	40	mm/rev	0,10–0,15	0,12–0,18	–	–
S4	–V38	WU40PH	WU40PH	35	40	65	mm/rev	0,14–0,21	0,16–0,24	0,18–0,26	0,20–0,30
S4	–DU	WU20PH	WU20PH	30	35	50	mm/rev	0,10–0,15	0,12–0,18	–	–

							Avanzamento al giro consigliato
		Grade		Cutting Speed vc m/min
Material Group	Geometry	center	periphery	Min	Start	Max	Tool Diameter	12,00 13,99 Insert Size A	14,00 18,99 Insert Size B	19,00 23,99 Insert Size C	24,00 29,99 Insert Size D
P0	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,06–0,08	0,08–0,11	0,10–0,13	0,11–0,14
P0	–DU	WU20PH	WU20PH	90	150	200	mm/rev	–	–	0.07–0.10	0.08–0.10
P1	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,06–0,10	0,08–0,13	0,10–0,15	0,11–0,16
P1	–DU	WU20PH	WU20PH	90	150	200	mm/rev	–	–	0.07–0.11	0.08–0.11
P2	–V34	WU40PH	WU25CH	120	190	280	mm/rev	0,06–0,10	0,08–0,15	0,10–0,16	0,11–0,17
P2	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0.07–0.12	0.08–0.13
P3	–V34	WU40PH	WPK10CH	120	200	310	mm/rev	0,08–0,15	0,10–0,16	0,11–0,18	0,12–0,20
P3	–DU	WU20PH	WU20PH	90	160	220	mm/rev	–	–	0.08–0.13	0.09–0.15
P4	–V34	WU40PH	WPK10CH	120	190	310	mm/rev	0,08–0,15	0,10–0,16	0,11–0,18	0,12–0,20
P4	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0.08–0.13	0.09–0.15
P5	–V36	WU40PH	WU25CH	120	180	250	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
P5	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0.07–0.11	0.08–0.12
P6	-V36	WU40PH	WU25CH	120	160	210	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
P6	–DU	WU20PH	WU20PH	90	130	165	mm/rev	–	–	0.07–0.11	0.08–0.12
M1	-V38	WU40PH	WU40PH	120	160	240	mm/rev	0,06–0,11	0,07–0,11	0,08–0,12	0,10–0,14
M1	–DU	WU20PH	WU20PH	90	130	190	mm/rev	–	–	0.06–0.09	0.07–0.10
M2	–V38	WU40PH	WU40PH	110	140	210	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
M2	–DU	WU20PH	WU20PH	110	140	190	mm/rev	–	–	0.06–0.09	0.07–0.10
M3	-V36	WU40PH	WU40PH	100	120	200	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
M3	–DU	WU20PH	WU20PH	80	100	160	mm/rev	–	–	0.06–0.09	0.07–0.10
K1	-V34	WU25CH	WPK10CH	120	200	280	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K1	–DU	WU20PH	WU20PH	90	160	220	mm/rev	–	–	0.07–0.13	0.09–0.18
K2	–V34	WU40PH	WPK10CH	100	180	260	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K2	–DU	WU20PH	WU20PH	80	140	200	mm/rev	–	–	0.07–0.13	0.09–0.18
K3	-V34	WU40PH	WPK10CH	100	170	240	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K3	–DU	WU20PH	WU20PH	80	140	190	mm/rev	–	–	0.07–0.13	0.09–0.18
N1	-V36	WN10PH	WN10PH	250	350	500	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
N2	–V36	WN10PH	WN10PH	150	300	450	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
N3	-V36	WN10PH	WN10PH	80	120	150	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
S3	-V38	WU40PH	WU40PH	20	30	45	mm/rev	0,08–0,12	0,08–0,13	0,10–0,15	0,12–0,19
S3	–DU	WU20PH	WU20PH	20	30	40	mm/rev	–	–	0.07–0.11	0.09–0.14
S4	–V38	WU40PH	WU40PH	35	40	65	mm/rev	0,08–0,12	0,08–0,13	0,10 –0,15	0,12–0,19
S4	–DU	WU20PH	WU20PH	30	40	60	mm/rev	–	–	0.07–0.11	0.09–0.14

Insert size	Diameter range mm (in)	2 x D/3 x D			4 x D			5 x D
Insert size	Diameter range mm (in)	X-offset value max. in mm (max. in inch)	D1 max value mm (in)	Hole tolerance mm (in)	X-offset value max. in mm (max. in inch)	D1 max value mm (in)	Hole tolerance mm (in)	X-offset value max. in mm (max. in inch)	D1 max value mm (in)	Hole tolerance mm (in)
A	12,00 13,99 (.473 .531)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
B	14,00 18,99 (.563 .734)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
C	19,00 23,99 (.750 .938)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
D	24,00 29,99 (.969 1.156)	0,8 (0.031)	D1 + 1,6mm (D1 + 0.063")	+/- 0,20 (+/- 0.008)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
E	30,00 36,99 (1.188 1.438)	0,8 (0.031)	D1 + 1,6mm (D1 + 0.063")	+/- 0,20 (+/- 0.008)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
F	37,00 45,99 (1.469 1.750)	0,8 (0.031)	D1 + 1,6mm (D1 + 0.063")	+/- 0,25 (+/- 0.010)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,38 (+/- 0.015)			+/- 0,38 (+/- 0.015)
G	46,00 56,99 (1.813 2.219)	1 (0.039)	D1 + 2mm (D1 + 0.079")	+/- 0,25 (+/- 0.010)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,38 (+/- 0.015)			+/- 0,38 (+/- 0.015)
H	57,00 68,00 (2.250 2.500)	1 (0.039)	D1 + 2mm (D1 + 0.079")	+/- 0,28 (+/- 0.011)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,42 (+/- 0.017)			+/- 0,42 (+/- 0.017)

Insert size	Diameter Range (mm)	2 x D and 3 x D		4 x D		5 x D
Insert size	Diameter Range (mm)	X-offset value max. in mm	D1 max value	X-offset value max. in mm	D1 max value	X-offset value max.	D1 max value
A	12,00 13,99	0,5	D1 + 1mm	0,5	D1 + 1mm
B	14,00 18,99	0,5	D1 + 1mm	0,5	D1 + 1mm
C	19,00 23,99	0,5	D1 + 1mm	0,5	D1 + 1mm
D	24,00 29,99	0,8	D1 + 1,6mm	0,8	D1 + 1mm
E	30,00 36,99	0,8	D1 + 1,6mm	0,8	D1 + 1mm
F	37,00 45,99	0,8	D1 + 1,6mm	0,8	D1 + 1mm
G	46,00 56,99	1	D1 + 2mm	0,8	D1 + 1mm
H	57,00 68,00	1	D1 + 2mm	0,8	D1 + 1mm

Insert size	Diameter range mm (in)	2 x D/3 x D		4 x D			5 x D
Insert size	Diameter range mm (in)	D1 max value mm (in)	Hole tolerance mm (in)	X-offset value max. in mm (max. in inch)	D1 max value mm (in)	Hole tolerance mm (in)	X-offset value max. in mm (max. in inch)	D1 max value mm (in)	Hole tolerance mm (in)
A	12,00 13,99 (.473 .531)	D1 + 1mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
B	14,00 18,99 (.563 .734)	D1 + 1mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
C	19,00 23,99 (.750 .938)	D1 + 1mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
D	24,00 29,99 (.969 1.156)	D1 + 1,6mm (D1 + 0.063")	+/- 0,20 (+/- 0.008)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
E	30,00 36,99 (1.188 1.438)	D1 + 1,6mm (D1 + 0.063")	+/- 0,20 (+/- 0.008)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
F	37,00 45,99 (1.469 1.750)	D1 + 1,6mm (D1 + 0.063")	+/- 0,25 (+/- 0.010)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,38 (+/- 0.015)			+/- 0,38 (+/- 0.015)
G	46,00 56,99 (1.813 2.219)	D1 + 2mm (D1 + 0.079")	+/- 0,25 (+/- 0.010)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,38 (+/- 0.015)			+/- 0,38 (+/- 0.015)
H	57,00 68,00 (2.250 2.500)	D1 + 2mm (D1 + 0.079")	+/- 0,28 (+/- 0.011)	0,8 (0.031)	D1 + 1mm (D1 + 0.039")	+/- 0,42 (+/- 0.017)			+/- 0,42 (+/- 0.017)

Material Group	Geometry	Grade		Cutting Speed SFM			Tool Diameter	1.188 1.438” Insert Size E	1.469 1.750” Insert Size F	1.813 2.219” Insert Size G	2.250 2.500” Insert Size H
Material Group	Geometry	center	periphery	Min	Start	Max	Tool Diameter	1.188 1.438” Insert Size E	1.469 1.750” Insert Size F	1.813 2.219” Insert Size G	2.250 2.500” Insert Size H
P0	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0051–0.0063	0.0059–0.0071	0.0063–0.0091	0.0067–0.0094
P0	– DU	WU20PH	WU20PH	290	430	624	IPR	0.0040–0.0050	0.0047–0.0057	–	–
P1	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0051–0.0071	0.0059–0.0079	0.0063–0.0106	0.0067–0.0114
P1	– DU	WU20PH	WU20PH	290	430	625	IPR	0.0040–0.0057	0.0047–0.0063	–	–
P2	–V34	WU40PH	WU25CH	360	570	840	IPR	0.0051–0.0079	0.0059–0.0083	0.0063–0.0110	0.0067–0.0118
P2	– DU	WU20PH	WU20PH	290	450	675	IPR	0.0040–0.0063	0.0047–0.0063	–	–
P3	–V34	WU40PH	WPK10CH	360	600	930	IPR	0.0053–0.0094	0.0063–0.0094	0.0071–0.0118	0.0075–0.0126
P3	– DU	WU20PH	WU20PH	290	480	745	IPR	0.0042–0.0075	0.0050–0.0075	–	–
P4	–V34	WU40PH	WPK10CH	360	570	930	IPR	0.0055–0.0087	0.0063–0.0094	0.0071–0.0118	0.0075–0.0126
P4	– DU	WU20PH	WU20PH	290	450	745	IPR	0.0044–0.0069	0.0050–0.0075	–	–
P5	–V36	WU40PH	WU25CH	360	540	750	IPR	0.0051–0.0071	0.0059–0.0079	0.0063–0.0110	0.0067–0.0118
P5	– DU	WU20PH	WU20PH	290	430	600	IPR	0.0040–0.0057	0.0047–0.0063	–	–
P6	-V36	WU40PH	WU25CH	360	480	630	IPR	0.0051–0.0071	0.0059–0.0079	0.0063–0.0110	0.0067–0.0114
P6	- DU	WU20PH	WU20PH	290	380	500	IPR	0.0040-0.0057	0.0047-0.0063	-	-
M1	-V38	WU40PH	WU40PH	360	480	720	IPR	0.0047–0.0079	0.0055–0.0098	0.0063–0.0110	0.0063–0.0118
M1	- DU	WU20PH	WU20PH	290	385	575	IPR	0.0038-0.0063	0.0044-0.0078	-	-
M2	–V38	WU40PH	WU40PH	330	420	630	IPR	0.0047–0.0079	0.0055–0.0098	0.0063–0.0110	0.0063–0.0118
M2	– DU	WU20PH	WU20PH	265	330	500	IPR	0.0038–0.0063	0.0044–0.0078	–	–
M3	-V36	WU40PH	WU40PH	300	360	600	IPR	0.0047–0.0079	0.0055–0.0098	0.0063–0.0110	0.0063–0.0118
M3	- DU	WU20PH	WU20PH	240	290	480	IPR	0.0038-0.0063	0.0044-0.0098	-	-
K1	-V34	WU25CH	WPK10CH	360	600	840	IPR	0.0055–0.0102	0.0063–0.0118	0.0071–0.0126	0.0079–0.0142
K1	- DU	WU20PH	WU20PH	290	480	670	IPR	0.0044-0.0081	0.0050-0.0094	-	-
K2	–V34	WU40PH	WPK10CH	300	540	780	IPR	0.0055–0.0102	0.0063–0.0118	0.0071–0.0126	0.0079–0.0142
K2	– DU	WU20PH	WU20PH	240	430	625	IPR	0.0044–0.0081	0.0050–0.0094	–	–
K3	-V34	WU40PH	WPK10CH	300	510	720	IPR	0.0055–0.0102	0.0063–0.0118	0.0071–0.0126	0.0079–0.0142
K3	- DU	WU20PH	WU20PH	240	400	575	IPR	0.0044-0.0081	0.0050-0.0094	-	-
N1	-V36	WN10PH	WN10PH	750	1050	1500	IPR	0.0051–0.0071	0.0059–0.0079	0.0063–0.0110	0.0067–0.0118
N2	–V36	WN10PH	WN10PH	450	900	1350	IPR	0.0051–0.0071	0.0059–0.0079	0.0063–0.0110	0.0067–0.0118
N3	-V36	WN10PH	WN10PH	240	360	450	IPR	0.0047–0.0067	0.0055–0.0083	0.0063–0.0091	0.0063–0.0094
S3	-V38	WU40PH	WU40PH	60	90	135	IPR	0.0055–0.0083	0.0063–0.0094	0.0071–0.0102	0.0079–0.0118
S3	- DU	WU20PH	WU20PH	50	70	100	IPR	0.0044-0.083	0.0050-0.0075	-	-
S4	–V38	WU40PH	WU40PH	105	120	195	IPR	0.0055–0.0083	0.0063–0.0094	0.0071–0.0102	0.0079–0.0118
S4	– DU	WU20PH	WU20PH	85	95	150	IPR	0.0044–0.0664	0.0050–0.0075	–	–

							Recommended Feed Rate per Revolution
Material Group	Geometry	Grade		Cutting Speed SFM			Tool Diameter	.473 .531" Insert Size A	.563 .734" Insert Size B	.750 .938" Insert Size C	.969 1.156" Insert Size D
Material Group	Geometry	center	periphery	Min	Start	Max	Tool Diameter	.473 .531" Insert Size A	.563 .734" Insert Size B	.750 .938" Insert Size C	.969 1.156" Insert Size D
P0	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0024–0.0031	0.0031–0.0043	0.0039–0.0051	0.0043–0.0055
P0	– DU	WU20PH	WU20PH	290	430	625	IPR	–	–	0.0031–0.0041	0.0034–0.0044
P1	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0024–0.0039	0.0031–0.0051	0.0039–0.0059	0.0043–0.0063
P1	– DU	WU20PH	WU20PH	290	430	625	IPR	–	–	0.0031–0.0047	0.0034–0.0050
P2	–V34	WU40PH	WU25CH	360	570	840	IPR	0.0024–0.0039	0.0031–0.0059	0.0039–0.0063	0.0043–0.0067
P2	– DU	WU20PH	WU20PH	290	450	675	IPR	–	–	0.0031–0.0050	0.0034–0.0054
P3	–V34	WU40PH	WPK10CH	360	600	930	IPR	0.0031–0.0059	0.0039–0.0063	0.0043–0.0071	0.0047–0.0079
P3	– DU	WU20PH	WU20PH	290	480	745	IPR	–	–	0.0034–0.0067	0.0037–0.0063
P4	–V34	WU40PH	WPK10CH	360	570	930	IPR	0.0031–0.0059	0.0039–0.0063	0.0043–0.0071	0.0047–0.0079
P4	– DU	WU20PH	WU20PH	290	450	745	IPR	–	–	0.0034–0.0067	0.0037–0.0063
P5	–V36	WU40PH	WU25CH	360	540	750	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
P5	– DU	WU20PH	WU20PH	290	430	600	IPR	–	–	0.0031–0.0047	0.0034–0.0050
P6	-V36	WU40PH	WU25CH	360	480	630	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
P6	-V36	WU40PH	WU25CH	290	385	500	IPR	-	-	0.0031-0.0047	0.0034-0.0050
M1	-V38	WU40PH	WU40PH	360	480	720	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M1	- DU	WU20PH	WU20PH	290	385	575	IPR	-	-	0.0025-0.0047	0.0031-0.0050
M2	–V38	WU40PH	WU40PH	330	420	630	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M2	– DU	WU20PH	WU20PH	265	340	500	IPR	–	–	0.0025–0.0047	0.0031–0.0050
M3	-V36	WU40PH	WU40PH	300	360	600	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M3	- DU	WU20PH	WU20PH	240	290	480	IPR	-	-	0.0025-0.0047	0.0031-0.0050
K1	-V34	WU25CH	WPK10CH	360	600	840	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K1	- DU	WU20PH	WU20PH	290	480	675	IPR	-	-	0.0031-0.0057	0.0038-0.0075
K2	–V34	WU40PH	WPK10CH	300	540	780	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K2	– DU	WU20PH	WU20PH	240	430	625	IPR	–	–	0.0031–0.0057	0.0038–0.0075
K3	-V34	WU40PH	WPK10CH	300	510	720	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K3	- DU	WU20PH	WU20PH	240	400	575	IPR	-	-	0.0031-0.0057	0.0038-0.0075
N1	-V36	WN10PH	WN10PH	750	1050	1500	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
N2	–V36	WN10PH	WN10PH	450	900	1350	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
N3	-V36	WN10PH	WN10PH	240	360	450	IPR	0.0024–0.0039	0.0028–0.0043	0.0031–0.0047	0.0039–0.0055
S3	-V38	WU40PH	WU40PH	60	90	135	IPR	0.0031–0.0047	0.0031–0.0051	0.0039–0.0059	0.0047–0.0075
S3	- DU	WU20PH	WU20PH	50	70	100	IPR	-	-	0.0031-0.0047	0.0038-0.006
S4	–V38	WU40PH	WU40PH	105	120	195	IPR	0.0031–0.0047	0.0031–0.0051	0.0039–0.0059	0.0047–0.0075
S4	– DU	WU20PH	WU20PH	85	95	150	IPR	–	–	0.0031–0.0047	0.0038–0.006

							Recommended Feed Rate per Revolution
Material Group	Geometry	Grade		Cutting Speed SFM			Tool Diameter	.473 .531" Insert Size A	.563 .734" Insert Size B	.750 .938" Insert Size C	.969 1.156" Insert Size D
Material Group	Geometry	center	periphery	Min	Start	Max	Tool Diameter	.473 .531" Insert Size A	.563 .734" Insert Size B	.750 .938" Insert Size C	.969 1.156" Insert Size D
P0	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0024–0.0031	0.0031–0.0043	0.0039–0.0051	0.0043–0.0055
P0	– DU	WU20PH	WU20PH	290	430	625	IPR	–	–	0.0031–0.0041	0.0034–0.0044
P1	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0024–0.0039	0.0031–0.0051	0.0039–0.0059	0.0043–0.0063
P1	– DU	WU20PH	WU20PH	290	430	625	IPR	–	–	0.0031–0.0047	0.0034–0.0050
P2	–V34	WU40PH	WU25CH	360	570	840	IPR	0.0024–0.0039	0.0031–0.0059	0.0039–0.0063	0.0043–0.0067
P2	– DU	WU20PH	WU20PH	290	450	675	IPR	–	–	0.0031–0.0050	0.0034–0.0054
P3	–V34	WU40PH	WPK10CH	360	600	930	IPR	0.0031–0.0059	0.0039–0.0063	0.0043–0.0071	0.0047–0.0079
P3	– DU	WU20PH	WU20PH	290	480	745	IPR	–	–	0.0034–0.0067	0.0037–0.0063
P4	–V34	WU40PH	WPK10CH	360	570	930	IPR	0.0031–0.0059	0.0039–0.0063	0.0043–0.0071	0.0047–0.0079
P4	– DU	WU20PH	WU20PH	290	450	745	IPR	–	–	0.0034–0.0067	0.0037–0.0063
P5	–V36	WU40PH	WU25CH	360	540	750	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
P5	– DU	WU20PH	WU20PH	290	430	600	IPR	–	–	0.0031–0.0047	0.0034–0.0050
P6	-V36	WU40PH	WU25CH	360	480	630	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
P6	-V36	WU40PH	WU25CH	290	385	500	IPR	-	-	0.0031-0.0047	0.0034-0.0050
M1	-V38	WU40PH	WU40PH	360	480	720	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M1	- DU	WU20PH	WU20PH	290	385	575	IPR	-	-	0.0025-0.0047	0.0031-0.0050
M2	–V38	WU40PH	WU40PH	330	420	630	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M2	– DU	WU20PH	WU20PH	265	340	500	IPR	–	–	0.0025–0.0047	0.0031–0.0050
M3	-V36	WU40PH	WU40PH	300	360	600	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M3	- DU	WU20PH	WU20PH	240	290	480	IPR	-	-	0.0025-0.0047	0.0031-0.0050
K1	-V34	WU25CH	WPK10CH	360	600	840	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K1	- DU	WU20PH	WU20PH	290	480	675	IPR	-	-	0.0031-0.0057	0.0038-0.0075
K2	–V34	WU40PH	WPK10CH	300	540	780	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K2	– DU	WU20PH	WU20PH	240	430	625	IPR	–	–	0.0031–0.0057	0.0038–0.0075
K3	-V34	WU40PH	WPK10CH	300	510	720	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K3	- DU	WU20PH	WU20PH	240	400	575	IPR	-	-	0.0031-0.0057	0.0038-0.0075
N1	-V36	WN10PH	WN10PH	750	1050	1500	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
N2	–V36	WN10PH	WN10PH	450	900	1350	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
N3	-V36	WN10PH	WN10PH	240	360	450	IPR	0.0024–0.0039	0.0028–0.0043	0.0031–0.0047	0.0039–0.0055
S3	-V38	WU40PH	WU40PH	60	90	135	IPR	0.0031–0.0047	0.0031–0.0051	0.0039–0.0059	0.0047–0.0075
S3	- DU	WU20PH	WU20PH	50	70	100	IPR	-	-	0.0031-0.0047	0.0038-0.006
S4	–V38	WU40PH	WU40PH	105	120	195	IPR	0.0031–0.0047	0.0031–0.0051	0.0039–0.0059	0.0047–0.0075
S4	– DU	WU20PH	WU20PH	85	95	150	IPR	–	–	0.0031–0.0047	0.0038–0.006

ようこそ

設定をご確認ください

設定の更新

提案製品

Product Family suggestions

営業チームにお問い合わせください

営業チームにお問い合わせください

ソリューション編集

ソリューション追加