Country

Lingua

Unità di misura

Suggerimenti sui prodotti

Top Cut 4 • 4 x D • SLR Shank • Inch

Name: Top Cut 4 • 4 x D • SLR Shank • Inch
SKU: 100014769
Rating: 0 (0 reviews)

TC4 • 4 x D • SLR Shanks • Inch

Uses and application

Shank - Cylindrical with Flat
Drilling
Drilling: Inclined Entry
Drilling: Inclined Exit
Drilling: X-Offset
Foratura: Convessa
Adduzione interna di refrigerante: Radiale: Foratura intercambiabile
Foratura: Foro cieco
Chain Drilling
Drilling: Cross-Hole Drilling
Drilling: Half-Cylindrical Drilling
Drilling: Corner Drilling 45°

Parti compatibili
Insert Selection

TC4 • Guida alla selezione degli inserti

Gruppo materiali	Geometria	Lavorazione leggera		Uso generico		Lavorazione pesante
Gruppo materiali	Geometria	inserto periferico	inserto centrale	inserto periferico	inserto centrale	inserto periferico	inserto centrale
P1	V38/DU	WU25CH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
P2–P4	V34/DU	WPK10CH	WU40PH/WU20PH	WU25CH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
P5–P6	V36/DU	WU25CH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
M1–M3	V36/DU	WU25CH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
K1–K3	V34/DU	WPK10CH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH
N1–N4	V36	WN10PH	WN10PH	WN10PH	WN10PH	WN10PH	WN10PH
S1–S4	V38/DU	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH	WU40PH/WU20PH

							Avanzamento al giro consigliato
Gruppo materiali	Geometria	Qualità		Velocità di taglio vc m/min			Diametro utensile	12,00 13,99 Dimensione dell’inserto A	14,00 18,99 Dimensione dell’inserto B	19,00 23,99 Dimensione dell’inserto C	24,00 29,99 Dimensione dell’inserto D
Gruppo materiali	Geometria	centrale	periferico	Min	Valore Iniziale	Max	Diametro utensile	12,00 13,99 Dimensione dell’inserto A	14,00 18,99 Dimensione dell’inserto B	19,00 23,99 Dimensione dell’inserto C	24,00 29,99 Dimensione dell’inserto D
P0	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,06–0,08	0,08–0,11	0,10–0,13	0,11–0,14
P0	–DU	WU20PH	WU20PH	90	150	200	mm/rev	–	–	0,07–0,10	0,08–0,10
P1	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,06–0,10	0,08–0,13	0,10–0,15	0,11–0,16
P1	–DU	WU20PH	WU20PH	90	150	200	mm/rev	–	–	0,07–0,11	0,08–0,11
P2	–V34	WU40PH	WU25CH	120	190	280	mm/rev	0,06–0,10	0,08–0,15	0,10–0,16	0,11–0,17
P2	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0,07–0,12	0,08–0,13
P3	–V34	WU40PH	WPK10CH	120	200	310	mm/rev	0,08–0,15	0,10–0,16	0,11–0,18	0,12–0,20
P3	–DU	WU20PH	WU20PH	90	160	220	mm/rev	–	–	0,08–0,13	0,09–0,15
P4	–V34	WU40PH	WPK10CH	120	190	310	mm/rev	0,08–0,15	0,10–0,16	0,11–0,18	0,12–0,20
P4	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0,08–0,13	0,09–0,15
P5	–V36	WU40PH	WU25CH	120	180	250	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
P5	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0,07–0,11	0,08–0,12
P6	-V36	WU40PH	WU25CH	120	160	210	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
P6	–DU	WU20PH	WU20PH	90	130	165	mm/rev	–	–	0,07–0,11	0,08–0,12
M1	-V38	WU40PH	WU40PH	120	160	240	mm/rev	0,06–0,11	0,07–0,11	0,08–0,12	0,10–0,14
M1	–DU	WU20PH	WU20PH	90	130	190	mm/rev	–	–	0,06–0,09	0,07–0,10
M2	–V38	WU40PH	WU40PH	110	140	210	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
M2	–DU	WU20PH	WU20PH	110	140	190	mm/rev	–	–	0,06–0,09	0,07–0,10
M3	-V36	WU40PH	WU40PH	100	120	200	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
M3	–DU	WU20PH	WU20PH	80	100	160	mm/rev	–	–	0,06–0,09	0,07–0,10
K1	-V34	WU25CH	WPK10CH	120	200	280	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K1	–DU	WU20PH	WU20PH	90	160	220	mm/rev	–	–	0,07–0,13	0,09–0,18
K2	–V34	WU40PH	WPK10CH	100	180	260	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K2	–DU	WU20PH	WU20PH	80	140	200	mm/rev	–	–	0,07–0,13	0,09–0,18
K3	-V34	WU40PH	WPK10CH	100	170	240	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K3	–DU	WU20PH	WU20PH	80	140	190	mm/rev	–	–	0,07–0,13	0,09–0,18
N1	-V36	WN10PH	WN10PH	250	350	500	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
N2	–V36	WN10PH	WN10PH	150	300	450	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
N3	-V36	WN10PH	WN10PH	80	120	150	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
S3	-V38	WU40PH	WU40PH	20	30	45	mm/rev	0,08–0,12	0,08–0,13	0,10–0,15	0,12–0,19
S3	–DU	WU20PH	WU20PH	20	30	40	mm/rev	–	–	0,07–0,11	0,09–0,14
S4	–V38	WU40PH	WU40PH	35	40	65	mm/rev	0,08–0,12	0,08–0,13	0,10 –0,15	0,12–0,19
S4	–DU	WU20PH	WU20PH	30	40	60	mm/rev	–	–	0,07–0,11	0,09–0,14

Gruppo materiali	Geometria	Qualità		Velocità di taglio vc m/min			Diametro utensile	30,00 36,99 Dimensione dell’inserto E	37,00 45,99 Dimensione dell’inserto F	46,00 56,99 Dimensione dell’inserto G	57,00 68,00 Dimensione dell’inserto H
Gruppo materiali	Geometria	centrale	periferico	Min	Valore Iniziale	Max	Diametro utensile	30,00 36,99 Dimensione dell’inserto E	37,00 45,99 Dimensione dell’inserto F	46,00 56,99 Dimensione dell’inserto G	57,00 68,00 Dimensione dell’inserto H
P0	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,13–0,16	0,15–0,18	0,16–0,23	0,17–0,24
P0	–DU	WU20PH	WU20PH	90	140	200	mm/rev	0,09–0,12	0,11–0,13	–	–
P1	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,13–0,17	0,15–0,19	0,16–0,24	0,17–0,25
P1	–DU	WU20PH	WU20PH	90	140	200	mm/rev	0,09–0,13	0,11–0,14	–	–
P2	–V34	WU40PH	WU25CH	120	190	280	mm/rev	0,13–0,20	0,15–0,21	0,16–0,28	0,17–0,30
P2	–DU	WU20PH	WU20PH	90	150	220	mm/rev	0,09–0,15	0,11–0,15	–	–
P3	–V34	WU40PH	WPK10CH	120	200	310	mm/rev	0,16–0,24	0,16–0,24	0,18–0,30	0,19–0,32
P3	–DU	WU20PH	WU20PH	90	160	250	mm/rev	0,12–0,16	0,12–0,18	–	–
P4	–V34	WU40PH	WPK10CH	120	190	310	mm/rev	0,14–0,22	0,16–0,24	0,18–0,30	0,19–0,32
P4	–DU	WU20PH	WU20PH	90	150	250	mm/rev	0,12–0,16	0,12–0,18	–	–
P5	–V36	WU40PH	WU25CH	120	180	250	mm/rev	0,13–0,18	0,15–0,20	0,16–0,28	0,17–0,30
P5	–DU	WU20PH	WU20PH	90	140	200	mm/rev	0,09–0,13	0,11–0,15	–	–
P6	-V36	WU40PH	WU25CH	120	160	210	mm/rev	0,13–0,18	0,15–0,20	0,16–0,28	0,17–0,29
P6	–DU	WU20PH	WU20PH	90	120	160	mm/rev	0,09–0,13	0,11–0,15	–	–
M1	-V38	WU40PH	WU40PH	120	160	240	mm/rev	0,12–0,17	0,14–0,21	0,16–0,23	0,16–0,24
M1	–DU	WU20PH	WU20PH	90	120	190	mm/rev	0,09–0,13	0,10–0,15	–	–
M2	–V38	WU40PH	WU40PH	110	140	210	mm/rev	0,12–0,17	0,14–0,21	0,16–0,23	0,16–0,24
M2	–DU	WU20PH	WU20PH	90	110	160	mm/rev	0,09–0,13	0,10–0,15	–	–
M3	-V36	WU40PH	WU40PH	100	120	200	mm/rev	0,12–0,17	0,14–0,21	0,16–0,23	0,16–0,24
M3	–DU	WU20PH	WU20PH	80	90	160	mm/rev	0,09–0,13	0,10–0,15	–	–
K1	-V34	WU25CH	WPK10CH	120	200	280	mm/rev	0,14–0,26	0,16–0,30	0,18–0,32	0,20–0,36
K1	–DU	WU20PH	WU20PH	90	160	220	mm/rev	0,10–0,19	0,12–0,22	–	–
K2	–V34	WU40PH	WPK10CH	100	180	260	mm/rev	0,14–0,26	0,16–0,30	0,18–0,32	0,20–0,36
K2	–DU	WU20PH	WU20PH	80	140	200	mm/rev	0,10–0,19	0,12–0,22	–	–
K3	-V34	WU40PH	WPK10CH	100	170	240	mm/rev	0,14–0,26	0,16–0,30	0,18–0,32	0,20–0,36
K3	–DU	WU20PH	WU20PH	80	130	190	mm/rev	0,10–0,19	0,12–0,22	–	–
N1	-V36	WN10PH	WN10PH	250	350	500	mm/rev	0,13–0,18	0,15–0,20	0,16–0,28	0,17–0,30
N2	–V36	WN10PH	WN10PH	150	300	450	mm/rev	0,13–0,18	0,15–0,20	0,16–0,28	0,17–0,30
N3	-V36	WN10PH	WN10PH	80	120	150	mm/rev	0,12–0,17	0,14–0,21	0,16–0,23	0,16–0,24
S3	-V38	WU40PH	WU40PH	20	30	45	mm/rev	0,14–0,21	0,16–0,24	0,18–0,26	0,20–0,30
S3	–DU	WU20PH	WU20PH	20	25	40	mm/rev	0,10–0,15	0,12–0,18	–	–
S4	–V38	WU40PH	WU40PH	35	40	65	mm/rev	0,14–0,21	0,16–0,24	0,18–0,26	0,20–0,30
S4	–DU	WU20PH	WU20PH	30	35	50	mm/rev	0,10–0,15	0,12–0,18	–	–

							Avanzamento al giro consigliato
		Qualità		Velocità di taglio vc m/min
Gruppo materiali	Geometria	centrale	periferico	Min	Valore Iniziale	Max	Diametro utensile	12,00 13,99 Insert Size A	14,00 18,99 Insert Size B	19,00 23,99 Insert Size C	24,00 29,99 Insert Size D
P0	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,06–0,08	0,08–0,11	0,10–0,13	0,11–0,14
P0	–DU	WU20PH	WU20PH	90	150	200	mm/rev	–	–	0.07–0.10	0.08–0.10
P1	–V38	WU40PH	WU25CH	120	180	260	mm/rev	0,06–0,10	0,08–0,13	0,10–0,15	0,11–0,16
P1	–DU	WU20PH	WU20PH	90	150	200	mm/rev	–	–	0.07–0.11	0.08–0.11
P2	–V34	WU40PH	WU25CH	120	190	280	mm/rev	0,06–0,10	0,08–0,15	0,10–0,16	0,11–0,17
P2	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0.07–0.12	0.08–0.13
P3	–V34	WU40PH	WPK10CH	120	200	310	mm/rev	0,08–0,15	0,10–0,16	0,11–0,18	0,12–0,20
P3	–DU	WU20PH	WU20PH	90	160	220	mm/rev	–	–	0.08–0.13	0.09–0.15
P4	–V34	WU40PH	WPK10CH	120	190	310	mm/rev	0,08–0,15	0,10–0,16	0,11–0,18	0,12–0,20
P4	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0.08–0.13	0.09–0.15
P5	–V36	WU40PH	WU25CH	120	180	250	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
P5	–DU	WU20PH	WU20PH	90	150	220	mm/rev	–	–	0.07–0.11	0.08–0.12
P6	-V36	WU40PH	WU25CH	120	160	210	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
P6	–DU	WU20PH	WU20PH	90	130	165	mm/rev	–	–	0.07–0.11	0.08–0.12
M1	-V38	WU40PH	WU40PH	120	160	240	mm/rev	0,06–0,11	0,07–0,11	0,08–0,12	0,10–0,14
M1	–DU	WU20PH	WU20PH	90	130	190	mm/rev	–	–	0.06–0.09	0.07–0.10
M2	–V38	WU40PH	WU40PH	110	140	210	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
M2	–DU	WU20PH	WU20PH	110	140	190	mm/rev	–	–	0.06–0.09	0.07–0.10
M3	-V36	WU40PH	WU40PH	100	120	200	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
M3	–DU	WU20PH	WU20PH	80	100	160	mm/rev	–	–	0.06–0.09	0.07–0.10
K1	-V34	WU25CH	WPK10CH	120	200	280	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K1	–DU	WU20PH	WU20PH	90	160	220	mm/rev	–	–	0.07–0.13	0.09–0.18
K2	–V34	WU40PH	WPK10CH	100	180	260	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K2	–DU	WU20PH	WU20PH	80	140	200	mm/rev	–	–	0.07–0.13	0.09–0.18
K3	-V34	WU40PH	WPK10CH	100	170	240	mm/rev	0,08–0,14	0,08–0,16	0,10–0,18	0,12–0,24
K3	–DU	WU20PH	WU20PH	80	140	190	mm/rev	–	–	0.07–0.13	0.09–0.18
N1	-V36	WN10PH	WN10PH	250	350	500	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
N2	–V36	WN10PH	WN10PH	150	300	450	mm/rev	0,06–0,10	0,08–0,14	0,10–0,15	0,11–0,16
N3	-V36	WN10PH	WN10PH	80	120	150	mm/rev	0,06–0,10	0,07–0,11	0,08–0,12	0,10–0,14
S3	-V38	WU40PH	WU40PH	20	30	45	mm/rev	0,08–0,12	0,08–0,13	0,10–0,15	0,12–0,19
S3	–DU	WU20PH	WU20PH	20	30	40	mm/rev	–	–	0.07–0.11	0.09–0.14
S4	–V38	WU40PH	WU40PH	35	40	65	mm/rev	0,08–0,12	0,08–0,13	0,10 –0,15	0,12–0,19
S4	–DU	WU20PH	WU20PH	30	40	60	mm/rev	–	–	0.07–0.11	0.09–0.14

Dimensione dell’inserto	Gamma di diametri mm (pollici)	2 x D/3 x D			4 x D			5 x D
Dimensione dell’inserto	Gamma di diametri mm (pollici)	Valore dell'offset sull'asse x max in mm (max in pollici)	Valore D1 max mm (pollici)	Tolleranza del foro mm (pollici)	Valore dell'offset sull'asse x max in mm (max in pollici)	Valore D1 max mm (pollici)	Tolleranza del foro mm (pollici)	Valore dell'offset sull'asse x max in mm (max in pollici)	Valore D1 max mm (pollici)	Tolleranza del foro mm (pollici)
A	12,00 13,99 (.473 .531)	0,5 (0.020)	D1 + 1 mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1 mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
B	14,00 18,99 (.563 .734)	0,5 (0.020)	D1 + 1 mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1 mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
C	19,00 23,99 (.750 .938)	0,5 (0.020)	D1 + 1 mm (D1 + 0.039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1 mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
D	24,00 29,99 (.969 1.156)	0,8 (0.031)	D1 + 1,6 mm (D1 + 0.063")	+/- 0,20 (+/- 0.008)	0,8 (0.031)	D1 + 1 mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
E	30,00 36,99 (1.188 1.438)	0,8 (0.031)	D1 + 1,6 mm (D1 + 0.063")	+/- 0,20 (+/- 0.008)	0,8 (0.031)	D1 + 1 mm (D1 + 0.039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
F	37,00 45,99 (1.469 1.750)	0,8 (0.031)	D1 + 1,6 mm (D1 + 0.063")	+/- 0,25 (+/- 0.010)	0,8 (0.031)	D1 + 1 mm (D1 + 0.039")	+/- 0,38 (+/- 0.015)			+/- 0,38 (+/- 0.015)
G	46,00 56,99 (1.813 2.219)	1 (0.039)	D1 + 2 mm (D1 + 0.079")	+/- 0,25 (+/- 0.010)	0,8 (0.031)	D1 + 1 mm (D1 + 0.039")	+/- 0,38 (+/- 0.015)			+/- 0,38 (+/- 0.015)
H	57,00 68,00 (2.250 2.500)	1 (0.039)	D1 + 2 mm (D1 + 0.079")	+/- 0,28 (+/- 0.011)	0,8 (0.031)	D1 + 1 mm (D1 + 0.039")	+/- 0,42 (+/- 0.017)			+/- 0,42 (+/- 0.017)

Dimensione dell’inserto	Gamma di diametri (mm)	2 x D e 3 x D		4 x D		5 x D
Dimensione dell’inserto	Gamma di diametri (mm)	Valore dell’offset sull’asse x max. in mm	D1 max valore	Valore dell’offset sull’asse x max. in mm	D1 max valore	offset sull’asse X valore max.	D1 max valore
A	12,00 13,99	0,5	D1 + 1mm	0,5	D1 + 1mm
B	14,00 18,99	0,5	D1 + 1mm	0,5	D1 + 1mm
C	19,00 23,99	0,5	D1 + 1mm	0,5	D1 + 1mm
D	24,00 29,99	0,8	D1 + 1,6mm	0,8	D1 + 1mm
E	30,00 36,99	0,8	D1 + 1,6mm	0,8	D1 + 1mm
F	37,00 45,99	0,8	D1 + 1,6mm	0,8	D1 + 1mm
G	46,00 56,99	1	D1 + 2mm	0,8	D1 + 1mm
H	57,00 68,00	1	D1 + 2mm	0,8	D1 + 1mm

Dimensione dell’inserto	Gamma di diametri mm (pollici)	2 x D/3 x D		4 x D			5 x D
Dimensione dell’inserto	Gamma di diametri mm (pollici)	Valore D1 max mm (pollici)	Tolleranza del foro mm (pollici)	Valore dell'offset sull'asse x max in mm (max in pollici)	Valore D1 max mm (pollici)	Tolleranza del foro mm (pollici)	Valore dell'offset sull'asse x max in mm (max in pollici)	Valore D1 max mm (pollici)	Tolleranza del foro mm (pollici)
A	12,00 13,99 (.473 .531)	D1 + 1 mm (D1 + 0,039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1 mm (D1 + 0,039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
B	14,00 18,99 (.563 .734)	D1 + 1 mm (D1 + 0,039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1 mm (D1 + 0,039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
C	19,00 23,99 (.750 .938)	D1 + 1 mm (D1 + 0,039")	+/- 0,20 (+/- 0.008)	0,5 (0.020)	D1 + 1 mm (D1 + 0,039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
D	24,00 29,99 (.969 1.156)	D1 + 1,6 mm (D1 + 0,063")	+/- 0,20 (+/- 0.008)	0,8 (0.031)	D1 + 1 mm (D1 + 0,039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
E	30,00 36,99 (1.188 1.438)	D1 + 1,6 mm (D1 + 0,063")	+/- 0,20 (+/- 0.008)	0,8 (0.031)	D1 + 1 mm (D1 + 0,039")	+/- 0,35 (+/- 0.014)			+/- 0,35 (+/- 0.014)
F	37,00 45,99 (1.469 1.750)	D1 + 1,6 mm (D1 + 0,063")	+/- 0,25 (+/- 0.010)	0,8 (0.031)	D1 + 1 mm (D1 + 0,039")	+/- 0,38 (+/- 0.015)			+/- 0,38 (+/- 0.015)
G	46,00 56,99 (1.813 2.219)	D1 + 2 mm (D1 + 0,079")	+/- 0,25 (+/- 0.010)	0,8 (0.031)	D1 + 1 mm (D1 + 0,039")	+/- 0,38 (+/- 0.015)			+/- 0,38 (+/- 0.015)
H	57,00 68,00 (2.250 2.500)	D1 + 2 mm (D1 + 0,079")	+/- 0,28 (+/- 0.011)	0,8 (0.031)	D1 + 1 mm (D1 + 0,039")	+/- 0,42 (+/- 0.017)			+/- 0,42 (+/- 0.017)

Gruppo materiali	Geometria	Qualità		Velocità di taglio SFM			Diametro utensile	1.188 1.438" Dimensione dell'inserto E	1.469 1.750" Dimensione dell'inserto F	1.813 2.219" Dimensione dell'inserto G	2.250 2.500" Dimensione dell'inserto H
Gruppo materiali	Geometria	centrale	periferico	Min	Valore Iniziale	Max	Diametro utensile	1.188 1.438" Dimensione dell'inserto E	1.469 1.750" Dimensione dell'inserto F	1.813 2.219" Dimensione dell'inserto G	2.250 2.500" Dimensione dell'inserto H
P0	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0051 0.0063	0.0059 0.0071	0.0063 0.0091	0.0067 0.0094
P0
P1	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0051 0.0071	0.0059 0.0079	0.0063 0.0106	0.0067 0.0114
P1
P2	–V34	WU40PH	WU25CH	360	570	840	IPR	0.0051 0.0079	0.0059 0.0083	0.0063 0.0110	0.0067 0.0118
P2
P3	–V34	WU40PH	WPK10CH	360	600	930	IPR	0.0053 0.0094	0.0063 0.0094	0.0071 0.0118	0.0075 0.0126
P3
P4	–V34	WU40PH	WPK10CH	360	570	930	IPR	0.0055 0.0087	0.0063 0.0094	0.0071 0.0118	0.0075 0.0126
P4
P5	–V36	WU40PH	WU25CH	360	540	750	IPR	0.0051 0.0071	0.0059 0.0079	0.0063 0.0110	0.0067 0.0118
P5
P6	-V36	WU40PH	WU25CH	360	480	630	IPR	0.0051 0.0071	0.0059 0.0079	0.0063 0.0110	0.0067 0.0114
P6
M1	-V38	WU40PH	WU40PH	360	480	720	IPR	0.0047 0.0079	0.0055 0.0098	0.0063 0.0110	0.0063 0.0118
M1
M2	–V38	WU40PH	WU40PH	330	420	630	IPR	0.0047 0.0079	0.0055 0.0098	0.0063 0.0110	0.0063 0.0118
M2
M3	-V36	WU40PH	WU40PH	300	360	600	IPR	0.0047 0.0079	0.0055 0.0098	0.0063 0.0110	0.0063 0.0118
M3
K1	-V34	WU25CH	WPK10CH	360	600	840	IPR	0.0055 0.0102	0.0063 0.0118	0.0071 0.0126	0.0079 0.0142
K1
K2	–V34	WU40PH	WPK10CH	300	540	780	IPR	0.0055 0.0102	0.0063 0.0118	0.0071 0.0126	0.0079 0.0142
K2
K3	-V34	WU40PH	WPK10CH	300	510	720	IPR	0.0055 0.0102	0.0063 0.0118	0.0071 0.0126	0.0079 0.0142
K3
N1	-V36	WN10PH	WN10PH	750	1050	1500	IPR	0.0051 0.0071	0.0059 0.0079	0.0063 0.0110	0.0067 0.0118
N2	–V36	WN10PH	WN10PH	450	900	1350	IPR	0.0051 0.0071	0.0059 0.0079	0.0063 0.0110	0.0067 0.0118
N3	-V36	WN10PH	WN10PH	240	360	450	IPR	0.0047 0.0067	0.0055 0.0083	0.0063 0.0091	0.0063 0.0094
S3	-V38	WU40PH	WU40PH	60	90	135	IPR	0.0055 0.0083	0.0063 0.0094	0.0071 0.0102	0.0079 0.0118
S3
S4	–V38	WU40PH	WU40PH	105	120	195	IPR	0.0055 0.0083	0.0063 0.0094	0.0071 0.0102	0.0079 0.0118
S4

							Velocità di avanzamento consigliata per giro
Gruppo materiali	Geometria	Qualità		Velocità di taglio SFM			Diametro utensile	0,473 0,531" Dimensione dell'inserto A	0,563 0,734" Dimensione dell'inserto B	0,750 0,938" Dimensione dell'inserto C	0,969 1,156" Dimensione dell'inserto D
Gruppo materiali	Geometria	centrale	periferico	Min	Valore Iniziale	Max	Diametro utensile	0,473 0,531" Dimensione dell'inserto A	0,563 0,734" Dimensione dell'inserto B	0,750 0,938" Dimensione dell'inserto C	0,969 1,156" Dimensione dell'inserto D
P0	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0024 0.0031	0.0031 0.0043	0.0039 0.0051	0.0043 0.0055
P0
P1	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0024 0.0039	0.0031 0.0051	0.0039 0.0059	0.0043 0.0063
P1
P2	–V34	WU40PH	WU25CH	360	570	840	IPR	0.0024 0.0039	0.0031 0.0059	0.0039 0.0063	0.0043 0.0067
P2
P3	–V34	WU40PH	WPK10CH	360	600	930	IPR	0.0031 0.0059	0.0039 0.0063	0.0043 0.0071	0.0047 0.0079
P3
P4	–V34	WU40PH	WPK10CH	360	570	930	IPR	0.0031 0.0059	0.0039 0.0063	0.0043 0.0071	0.0047 0.0079
P4
P5	–V36	WU40PH	WU25CH	360	540	750	IPR	0.0024 0.0039	0.0031 0.0055	0.0039 0.0059	0.0043 0.0063
P5
P6	-V36	WU40PH	WU25CH	360	480	630	IPR	0.0024 0.0039	0.0031 0.0055	0.0039 0.0059	0.0043 0.0063
P6
M1	-V38	WU40PH	WU40PH	360	480	720	IPR	0.0024 0.0047	0.0028 0.0051	0.0031 0.0059	0.0039 0.0063
M1
M2	–V38	WU40PH	WU40PH	330	420	630	IPR	0.0024 0.0047	0.0028 0.0051	0.0031 0.0059	0.0039 0.0063
M2
M3	-V36	WU40PH	WU40PH	300	360	600	IPR	0.0024 0.0047	0.0028 0.0051	0.0031 0.0059	0.0039 0.0063
M3
K1	-V34	WU25CH	WPK10CH	360	600	840	IPR	0.0031 0.0055	0.0031 0.0063	0.0039 0.0071	0.0047 0.0094
K1
K2	–V34	WU40PH	WPK10CH	300	540	780	IPR	0.0031 0.0055	0.0031 0.0063	0.0039 0.0071	0.0047 0.0094
K2
K3	-V34	WU40PH	WPK10CH	300	510	720	IPR	0.0031 0.0055	0.0031 0.0063	0.0039 0.0071	0.0047 0.0094
K3
N1	-V36	WN10PH	WN10PH	750	1050	1500	IPR	0.0024 0.0039	0.0031 0.0055	0.0039 0.0059	0.0043 0.0063
N2	–V36	WN10PH	WN10PH	450	900	1350	IPR	0.0024 0.0039	0.0031 0.0055	0.0039 0.0059	0.0043 0.0063
N3	-V36	WN10PH	WN10PH	240	360	450	IPR	0.0024 0.0039	0.0028 0.0043	0.0031 0.0047	0.0039 0.0055
S3	-V38	WU40PH	WU40PH	60	90	135	IPR	0.0031 0.0047	0.0031 0.0051	0.0039 0.0059	0.0047 0.0075
S3
S4	–V38	WU40PH	WU40PH	105	120	195	IPR	0.0031 0.0047	0.0031 0.0051	0.0039 0.0059	0.0047 0.0075
S4

							Recommended Feed Rate per Revolution
Gruppo materiali	Geometria	Qualità		Velocità di taglio SFM			Diametro utensile	.473 .531" Insert Size A	.563 .734" Insert Size B	.750 .938" Insert Size C	.969 1.156" Insert Size D
Gruppo materiali	Geometria	centrale	periferico	Min	Valore Iniziale	Max	Diametro utensile	.473 .531" Insert Size A	.563 .734" Insert Size B	.750 .938" Insert Size C	.969 1.156" Insert Size D
P0	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0024–0.0031	0.0031–0.0043	0.0039–0.0051	0.0043–0.0055
P0	– DU	WU20PH	WU20PH	290	430	625	IPR	–	–	0.0031–0.0041	0.0034–0.0044
P1	–V38	WU40PH	WU25CH	360	540	780	IPR	0.0024–0.0039	0.0031–0.0051	0.0039–0.0059	0.0043–0.0063
P1	– DU	WU20PH	WU20PH	290	430	625	IPR	–	–	0.0031–0.0047	0.0034–0.0050
P2	–V34	WU40PH	WU25CH	360	570	840	IPR	0.0024–0.0039	0.0031–0.0059	0.0039–0.0063	0.0043–0.0067
P2	– DU	WU20PH	WU20PH	290	450	675	IPR	–	–	0.0031–0.0050	0.0034–0.0054
P3	–V34	WU40PH	WPK10CH	360	600	930	IPR	0.0031–0.0059	0.0039–0.0063	0.0043–0.0071	0.0047–0.0079
P3	– DU	WU20PH	WU20PH	290	480	745	IPR	–	–	0.0034–0.0067	0.0037–0.0063
P4	–V34	WU40PH	WPK10CH	360	570	930	IPR	0.0031–0.0059	0.0039–0.0063	0.0043–0.0071	0.0047–0.0079
P4	– DU	WU20PH	WU20PH	290	450	745	IPR	–	–	0.0034–0.0067	0.0037–0.0063
P5	–V36	WU40PH	WU25CH	360	540	750	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
P5	– DU	WU20PH	WU20PH	290	430	600	IPR	–	–	0.0031–0.0047	0.0034–0.0050
P6	-V36	WU40PH	WU25CH	360	480	630	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
P6	-V36	WU40PH	WU25CH	290	385	500	IPR	-	-	0.0031-0.0047	0.0034-0.0050
M1	-V38	WU40PH	WU40PH	360	480	720	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M1	- DU	WU20PH	WU20PH	290	385	575	IPR	-	-	0.0025-0.0047	0.0031-0.0050
M2	–V38	WU40PH	WU40PH	330	420	630	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M2	– DU	WU20PH	WU20PH	265	340	500	IPR	–	–	0.0025–0.0047	0.0031–0.0050
M3	-V36	WU40PH	WU40PH	300	360	600	IPR	0.0024–0.0047	0.0028–0.0051	0.0031–0.0059	0.0039–0.0063
M3	- DU	WU20PH	WU20PH	240	290	480	IPR	-	-	0.0025-0.0047	0.0031-0.0050
K1	-V34	WU25CH	WPK10CH	360	600	840	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K1	- DU	WU20PH	WU20PH	290	480	675	IPR	-	-	0.0031-0.0057	0.0038-0.0075
K2	–V34	WU40PH	WPK10CH	300	540	780	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K2	– DU	WU20PH	WU20PH	240	430	625	IPR	–	–	0.0031–0.0057	0.0038–0.0075
K3	-V34	WU40PH	WPK10CH	300	510	720	IPR	0.0031–0.0055	0.0031–0.0063	0.0039–0.0071	0.0047–0.0094
K3	- DU	WU20PH	WU20PH	240	400	575	IPR	-	-	0.0031-0.0057	0.0038-0.0075
N1	-V36	WN10PH	WN10PH	750	1050	1500	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
N2	–V36	WN10PH	WN10PH	450	900	1350	IPR	0.0024–0.0039	0.0031–0.0055	0.0039–0.0059	0.0043–0.0063
N3	-V36	WN10PH	WN10PH	240	360	450	IPR	0.0024–0.0039	0.0028–0.0043	0.0031–0.0047	0.0039–0.0055
S3	-V38	WU40PH	WU40PH	60	90	135	IPR	0.0031–0.0047	0.0031–0.0051	0.0039–0.0059	0.0047–0.0075
S3	- DU	WU20PH	WU20PH	50	70	100	IPR	-	-	0.0031-0.0047	0.0038-0.006
S4	–V38	WU40PH	WU40PH	105	120	195	IPR	0.0031–0.0047	0.0031–0.0051	0.0039–0.0059	0.0047–0.0075
S4	– DU	WU20PH	WU20PH	85	95	150	IPR	–	–	0.0031–0.0047	0.0038–0.006

Benvenuto

Conferma le tue preferenze

Aggiorna preferenze

Suggerimenti sui prodotti

Product Family suggestions

Contatta il Team di vendita

Contatta il Team di vendita

Modifica della soluzione

Soluzione aggiunta

Top Cut 4 • 4 x D • SLR Shank • Inch

TC4 • 4 x D • SLR Shanks • Inch

Uses and application

TC4 • Guida alla selezione degli inserti

Suggerimenti sui prodotti

Product Family suggestions

Contatta il Team di vendita

Notifications

Contatta il Team di vendita

Sending to {{cadTool}} in progress...

Top Cut 4 • 4 x D • SLR Shank • Inch

TC4 • 4 x D • SLR Shanks • Inch

Uses and application

TC4 • Guida alla selezione degli inserti

The following files are available