Bienvenue
Veuillez confirmer vos préférences
Mettre à jour les préférences

Suggestions de produit

Product Family suggestions

WIDIA à votre service

Support Clients

Trouver les coordonnées des supports clients dans le monde

Commande rapide
Article(s) ajoutées avec succès au panier
Voir le panier
Outils de coupe performants disponibles. Achetez dès à présent

    Couple et puissance de la fraise à plaquette indexable KM

    Pour fraise à plaquette indexable avec outil à changement rapide KM

    These calculations are based upon theoretical values and are only intended for planning purposes. Actual results will vary. No responsibility from Kennametal is assumed.

    Conversion of Workpiece Material Rockwell (Optional):
    Metric
    Inch

    Conversion of Workpiece Material Rockwell (Optional)

    Skip this step if you already know the Brinell hardness number(HB)
    Characteristics of Workpiece Materials

    Characteristics of Workpiece Materials

    HB
    PSI N/mm 2
    Ultimate Strength shown for generic steel. Please enter the actual value of your workpiece material if available&#44 for better accuracy You may look up this info through websites such as www.matweb.com
    End Mill Nomenclature

    End Mill Nomenclature

    in.mm.
    in. mm.
    in. mm.

    Machining Conditions

    sfm m/min
    in.(DOC) mm (DOC)
    in.(WOC) mm(WOC)
    in. IPT (chip load) mm
    Most Common Workpiece MaterialsCm at W/D ratios:
    W/D < = 0.660.66 < W/D < 1.0W/D = 1.0
    Aluminum alloys1.01.051.1
    Carbon and alloy steels1.01.151.3
    Cast irons1.01.151.3
    Titanium alloys1.01.201.4
    Stainless steel&#44 High-temperature alloys2.02.152.3
    MillingDepth of cutFeed per toothCw
    Category(min-max), in.(min-max), in.&nbsp;
    Light0.020-0.1000.003-0.0061.1
    Medium0.100-0.2000.006-0.0101.2
    Heavy duty0.200-0.4000.010-0.0201.3
       
    Direct Belt Drive.9
    Back Gear Drive.75
    Geared Head Drive.7-.8
    Oil - Hydraulic Drive.6-.9

    Safe Operating Conditions

    lbN
    lbN
    ft lbNm
    ft lbNm

    Calculated Machining Conditions

    RPM
    (IPM)(no productivity formula)mm/min
    in (chip load at the cut) mm/min
    (IPM)(with productivity formula)mm/min
    in.3/min MRRcm3/min3
    in.2mm2

    Calculated Required Power

    lbf should not exceed Ft maxN
    ft-lb should not exceed TpNm

    Machining Power

    HPckW
    hpkW
    Vous êtes sur le point d’ajouter à votre page mes solutions. Souhaitez-vous continuer ?
    Select the destination where you want to move à.
    Nouvelle Folder
      • Applied Filters:
      • Clear All

    A folder with the name already exists.

    Veuillez saisir un nom valide
    product-image
    Please adjust the following properties from

    catalogue ISO

    catalogue ANSI

    to find similar products.

    The following files are available

    Please select a file to download

    Models

    Product data

    I have read and accepted the Terms & Conditions of use

    Can’t find the file type you’re looking for?

    Vous devez être connecté pour voir les informations de votre tableau de bord
    Session expired due to inactivity, please login again
    Le(s) produit(s) () que vous essayez d’ajouter au panier est/sont indisponible(s), veuillez Contacter le service client.
    article(s) ajouté(s) avec succès au panier
    View Cart

    . Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.

    Minimum quantity should be

    SAP Material Numbercatalogue ISOGrade  

    You are about to leave the Solution building process.

    Are you sure you want to leave?