WIDIA steht Ihnen zur Diensten
WIDIA steht Ihnen zur Diensten
Verkauft in Pkg. von 0
Downloaded file will be available after import in the SolidCAM tool library.
| SAP-Materialnummer | 5578406 |
| ISO Katalognummer | TCF0750R3SLR100C |
| ANSI Katalognummer | TCF0750R3SLR100C |
| [D1] Bohrerdurchmesser M | 19.05 mm |
| [D1] Bohrerdurchmesser M | .75 in |
| [D1MAX] Bohrerdurchmesser max. | 19.548 mm |
| [D1MAX] Bohrerdurchmesser max. | .7696 in |
| [D] Adapter/Schaft/Bohrungsdurchmesser | 25.4 mm |
| [D] Adapter/Schaft/Bohrungsdurchmesser | 1 in |
| [L1] Messlänge der Wendeschneidplatte | 82.799 mm |
| [L1] Messlänge der Wendeschneidplatte | 3.259 in |
| [L4] Maximale Bohrtiefe | 57.83 mm |
| [L4] Maximale Bohrtiefe | 2.277 in |
| [L5] Bohrerspitzenlänge | 0.68 mm |
| [L5] Bohrerspitzenlänge | .0268 in |
| [LS] Schaftlänge | 56 mm |
| [LS] Schaftlänge | 2.204 in |
| [CS] Kühlmittelzufuhrgröße | 1/4 - 18 NPT |
| [SSC] Wendeschneidplatten-Sitz-Größe | C |
| Wendeschneidplatten-Größe | TCF070306CP |
| Maß-Wendeschneidplatte 2 | TCF070304CC |
Zylinderschaft – mit Spannfläche
Drilling
Drilling: Inclined Entry
Drilling: Inclined Exit
Drilling: X-Offset
Bohren: Konvexe Eintrittsfläche
Innere Kühlmittelzuführung: Radial: Bohren mit Wendeschneidplatten
Bohren: Sacklochbohrung
Chain Drilling
Drilling: Cross-Hole Drilling
Drilling: Half-Cylindrical Drilling
Drilling: Corner Drilling 45°| Material Group | Geometry | Light
|
General
|
Heavy
|
|||
| periphery
|
center
|
periphery
|
center
|
periphery
|
center
|
||
| P1 | V38/DU | WU25CH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH |
| P2–P4 | V34/DU | WPK10CH | WU40PH/WU20PH | WU25CH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH |
| P5–P6 | V36/DU | WU25CH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH |
| M1–M3 | V36/DU | WU25CH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH |
| K1–K3 | V34/DU | WPK10CH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH |
| N1–N4 | V36 | WN10PH | WN10PH | WN10PH | WN10PH | WN10PH | WN10PH |
| S1–S4 | V38/DU | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH | WU40PH/WU20PH |
| Recommended Feed Rate per Revolution | |||||||||||
| Material
|
Geometry | Grade | Cutting Speed
|
Tool
|
12,00
|
14,00
|
19,00
|
24,00
|
|||
| center | periphery | Min | Start | Max | |||||||
| P0 | –V38 | WU40PH | WU25CH | 120 | 180 | 260 | mm/rev | 0,06–0,08 | 0,08–0,11 | 0,10–0,13 | 0,11–0,14 |
| –DU | WU20PH | WU20PH | 90 | 150 | 200 | mm/rev | – | – | 0,07–0,10 | 0,08–0,10 | |
| P1 | –V38 | WU40PH | WU25CH | 120 | 180 | 260 | mm/rev | 0,06–0,10 | 0,08–0,13 | 0,10–0,15 | 0,11–0,16 |
| –DU | WU20PH | WU20PH | 90 | 150 | 200 | mm/rev | – | – | 0,07–0,11 | 0,08–0,11 | |
| P2 | –V34 | WU40PH | WU25CH | 120 | 190 | 280 | mm/rev | 0,06–0,10 | 0,08–0,15 | 0,10–0,16 | 0,11–0,17 |
| –DU | WU20PH | WU20PH | 90 | 150 | 220 | mm/rev | – | – | 0,07–0,12 | 0,08–0,13 | |
| P3 | –V34 | WU40PH | WPK10CH | 120 | 200 | 310 | mm/rev | 0,08–0,15 | 0,10–0,16 | 0,11–0,18 | 0,12–0,20 |
| –DU | WU20PH | WU20PH | 90 | 160 | 220 | mm/rev | – | – | 0,08–0,13 | 0,09–0,15 | |
| P4 | –V34 | WU40PH | WPK10CH | 120 | 190 | 310 | mm/rev | 0,08–0,15 | 0,10–0,16 | 0,11–0,18 | 0,12–0,20 |
| –DU | WU20PH | WU20PH | 90 | 150 | 220 | mm/rev | – | – | 0,08–0,13 | 0,09–0,15 | |
| P5 | –V36 | WU40PH | WU25CH | 120 | 180 | 250 | mm/rev | 0,06–0,10 | 0,08–0,14 | 0,10–0,15 | 0,11–0,16 |
| –DU | WU20PH | WU20PH | 90 | 150 | 220 | mm/rev | – | – | 0,07–0,11 | 0,08–0,12 | |
| P6 | -V36 | WU40PH | WU25CH | 120 | 160 | 210 | mm/rev | 0,06–0,10 | 0,08–0,14 | 0,10–0,15 | 0,11–0,16 |
| –DU | WU20PH | WU20PH | 90 | 130 | 165 | mm/rev | – | – | 0,07–0,11 | 0,08–0,12 | |
| M1 | -V38 | WU40PH | WU40PH | 120 | 160 | 240 | mm/rev | 0,06–0,11 | 0,07–0,11 | 0,08–0,12 | 0,10–0,14 |
| –DU | WU20PH | WU20PH | 90 | 130 | 190 | mm/rev | – | – | 0,06–0,09 | 0,07–0,10 | |
| M2 | –V38 | WU40PH | WU40PH | 110 | 140 | 210 | mm/rev | 0,06–0,10 | 0,07–0,11 | 0,08–0,12 | 0,10–0,14 |
| –DU | WU20PH | WU20PH | 110 | 140 | 190 | mm/rev | – | – | 0,06–0,09 | 0,07–0,10 | |
| M3 | -V36 | WU40PH | WU40PH | 100 | 120 | 200 | mm/rev | 0,06–0,10 | 0,07–0,11 | 0,08–0,12 | 0,10–0,14 |
| –DU | WU20PH | WU20PH | 80 | 100 | 160 | mm/rev | – | – | 0,06–0,09 | 0,07–0,10 | |
| K1 | -V34 | WU25CH | WPK10CH | 120 | 200 | 280 | mm/rev | 0,08–0,14 | 0,08–0,16 | 0,10–0,18 | 0,12–0,24 |
| –DU | WU20PH | WU20PH | 90 | 160 | 220 | mm/rev | – | – | 0,07–0,13 | 0,09–0,18 | |
| K2 | –V34 | WU40PH | WPK10CH | 100 | 180 | 260 | mm/rev | 0,08–0,14 | 0,08–0,16 | 0,10–0,18 | 0,12–0,24 |
| –DU | WU20PH | WU20PH | 80 | 140 | 200 | mm/rev | – | – | 0,07–0,13 | 0,09–0,18 | |
| K3 | -V34 | WU40PH | WPK10CH | 100 | 170 | 240 | mm/rev | 0,08–0,14 | 0,08–0,16 | 0,10–0,18 | 0,12–0,24 |
| –DU | WU20PH | WU20PH | 80 | 140 | 190 | mm/rev | – | – | 0,07–0,13 | 0,09–0,18 | |
| N1 | -V36 | WN10PH | WN10PH | 250 | 350 | 500 | mm/rev | 0,06–0,10 | 0,08–0,14 | 0,10–0,15 | 0,11–0,16 |
| N2 | –V36 | WN10PH | WN10PH | 150 | 300 | 450 | mm/rev | 0,06–0,10 | 0,08–0,14 | 0,10–0,15 | 0,11–0,16 |
| N3 | -V36 | WN10PH | WN10PH | 80 | 120 | 150 | mm/rev | 0,06–0,10 | 0,07–0,11 | 0,08–0,12 | 0,10–0,14 |
| S3 | -V38 | WU40PH | WU40PH | 20 | 30 | 45 | mm/rev | 0,08–0,12 | 0,08–0,13 | 0,10–0,15 | 0,12–0,19 |
| –DU | WU20PH | WU20PH | 20 | 30 | 40 | mm/rev | – | – | 0,07–0,11 | 0,09–0,14 | |
| S4 | –V38 | WU40PH | WU40PH | 35 | 40 | 65 | mm/rev | 0,08–0,12 | 0,08–0,13 | 0,10 –0,15 | 0,12–0,19 |
| –DU | WU20PH | WU20PH | 30 | 40 | 60 | mm/rev | – | – | 0,07–0,11 | 0,09–0,14 | |
| Material
|
Geometry | Grade | Cutting Speed
|
Tool
|
30,00
|
37,00
|
46,00
|
57,00
|
|||
| center | periphery | Min | Start | Max | |||||||
| P0 | –V38 | WU40PH | WU25CH | 120 | 180 | 260 | mm/rev | 0,13–0,16 | 0,15–0,18 | 0,16–0,23 | 0,17–0,24 |
| –DU | WU20PH | WU20PH | 90 | 140 | 200 | mm/rev | 0,09–0,12 | 0,11–0,13 | – | – | |
| P1 | –V38 | WU40PH | WU25CH | 120 | 180 | 260 | mm/rev | 0,13–0,17 | 0,15–0,19 | 0,16–0,24 | 0,17–0,25 |
| –DU | WU20PH | WU20PH | 90 | 140 | 200 | mm/rev | 0,09–0,13 | 0,11–0,14 | – | – | |
| P2 | –V34 | WU40PH | WU25CH | 120 | 190 | 280 | mm/rev | 0,13–0,20 | 0,15–0,21 | 0,16–0,28 | 0,17–0,30 |
| –DU | WU20PH | WU20PH | 90 | 150 | 220 | mm/rev | 0,09–0,15 | 0,11–0,15 | – | – | |
| P3 | –V34 | WU40PH | WPK10CH | 120 | 200 | 310 | mm/rev | 0,16–0,24 | 0,16–0,24 | 0,18–0,30 | 0,19–0,32 |
| –DU | WU20PH | WU20PH | 90 | 160 | 250 | mm/rev | 0,12–0,16 | 0,12–0,18 | – | – | |
| P4 | –V34 | WU40PH | WPK10CH | 120 | 190 | 310 | mm/rev | 0,14–0,22 | 0,16–0,24 | 0,18–0,30 | 0,19–0,32 |
| –DU | WU20PH | WU20PH | 90 | 150 | 250 | mm/rev | 0,12–0,16 | 0,12–0,18 | – | – | |
| P5 | –V36 | WU40PH | WU25CH | 120 | 180 | 250 | mm/rev | 0,13–0,18 | 0,15–0,20 | 0,16–0,28 | 0,17–0,30 |
| –DU | WU20PH | WU20PH | 90 | 140 | 200 | mm/rev | 0,09–0,13 | 0,11–0,15 | – | – | |
| P6 | -V36 | WU40PH | WU25CH | 120 | 160 | 210 | mm/rev | 0,13–0,18 | 0,15–0,20 | 0,16–0,28 | 0,17–0,29 |
| –DU | WU20PH | WU20PH | 90 | 120 | 160 | mm/rev | 0,09–0,13 | 0,11–0,15 | – | – | |
| M1 | -V38 | WU40PH | WU40PH | 120 | 160 | 240 | mm/rev | 0,12–0,17 | 0,14–0,21 | 0,16–0,23 | 0,16–0,24 |
| –DU | WU20PH | WU20PH | 90 | 120 | 190 | mm/rev | 0,09–0,13 | 0,10–0,15 | – | – | |
| M2 | –V38 | WU40PH | WU40PH | 110 | 140 | 210 | mm/rev | 0,12–0,17 | 0,14–0,21 | 0,16–0,23 | 0,16–0,24 |
| –DU | WU20PH | WU20PH | 90 | 110 | 160 | mm/rev | 0,09–0,13 | 0,10–0,15 | – | – | |
| M3 | -V36 | WU40PH | WU40PH | 100 | 120 | 200 | mm/rev | 0,12–0,17 | 0,14–0,21 | 0,16–0,23 | 0,16–0,24 |
| –DU | WU20PH | WU20PH | 80 | 90 | 160 | mm/rev | 0,09–0,13 | 0,10–0,15 | – | – | |
| K1 | -V34 | WU25CH | WPK10CH | 120 | 200 | 280 | mm/rev | 0,14–0,26 | 0,16–0,30 | 0,18–0,32 | 0,20–0,36 |
| –DU | WU20PH | WU20PH | 90 | 160 | 220 | mm/rev | 0,10–0,19 | 0,12–0,22 | – | – | |
| K2 | –V34 | WU40PH | WPK10CH | 100 | 180 | 260 | mm/rev | 0,14–0,26 | 0,16–0,30 | 0,18–0,32 | 0,20–0,36 |
| –DU | WU20PH | WU20PH | 80 | 140 | 200 | mm/rev | 0,10–0,19 | 0,12–0,22 | – | – | |
| K3 | -V34 | WU40PH | WPK10CH | 100 | 170 | 240 | mm/rev | 0,14–0,26 | 0,16–0,30 | 0,18–0,32 | 0,20–0,36 |
| –DU | WU20PH | WU20PH | 80 | 130 | 190 | mm/rev | 0,10–0,19 | 0,12–0,22 | – | – | |
| N1 | -V36 | WN10PH | WN10PH | 250 | 350 | 500 | mm/rev | 0,13–0,18 | 0,15–0,20 | 0,16–0,28 | 0,17–0,30 |
| N2 | –V36 | WN10PH | WN10PH | 150 | 300 | 450 | mm/rev | 0,13–0,18 | 0,15–0,20 | 0,16–0,28 | 0,17–0,30 |
| N3 | -V36 | WN10PH | WN10PH | 80 | 120 | 150 | mm/rev | 0,12–0,17 | 0,14–0,21 | 0,16–0,23 | 0,16–0,24 |
| S3 | -V38 | WU40PH | WU40PH | 20 | 30 | 45 | mm/rev | 0,14–0,21 | 0,16–0,24 | 0,18–0,26 | 0,20–0,30 |
| –DU | WU20PH | WU20PH | 20 | 25 | 40 | mm/rev | 0,10–0,15 | 0,12–0,18 | – | – | |
| S4 | –V38 | WU40PH | WU40PH | 35 | 40 | 65 | mm/rev | 0,14–0,21 | 0,16–0,24 | 0,18–0,26 | 0,20–0,30 |
| –DU | WU20PH | WU20PH | 30 | 35 | 50 | mm/rev | 0,10–0,15 | 0,12–0,18 | – | – | |
| Avanzamento al giro consigliato | |||||||||||
| Grade | Cutting Speed
|
||||||||||
| Material
|
Geometry | center | periphery | Min | Start | Max | Tool
|
12,00
|
14,00
|
19,00
|
24,00
|
| P0 | –V38 | WU40PH | WU25CH | 120 | 180 | 260 | mm/rev | 0,06–0,08 | 0,08–0,11 | 0,10–0,13 | 0,11–0,14 |
| P0 | –DU | WU20PH | WU20PH | 90 | 150 | 200 | mm/rev | – | – | 0.07–0.10 | 0.08–0.10 |
| P1 | –V38 | WU40PH | WU25CH | 120 | 180 | 260 | mm/rev | 0,06–0,10 | 0,08–0,13 | 0,10–0,15 | 0,11–0,16 |
| P1 | –DU | WU20PH | WU20PH | 90 | 150 | 200 | mm/rev | – | – | 0.07–0.11 | 0.08–0.11 |
| P2 | –V34 | WU40PH | WU25CH | 120 | 190 | 280 | mm/rev | 0,06–0,10 | 0,08–0,15 | 0,10–0,16 | 0,11–0,17 |
| P2 | –DU | WU20PH | WU20PH | 90 | 150 | 220 | mm/rev | – | – | 0.07–0.12 | 0.08–0.13 |
| P3 | –V34 | WU40PH | WPK10CH | 120 | 200 | 310 | mm/rev | 0,08–0,15 | 0,10–0,16 | 0,11–0,18 | 0,12–0,20 |
| P3 | –DU | WU20PH | WU20PH | 90 | 160 | 220 | mm/rev | – | – | 0.08–0.13 | 0.09–0.15 |
| P4 | –V34 | WU40PH | WPK10CH | 120 | 190 | 310 | mm/rev | 0,08–0,15 | 0,10–0,16 | 0,11–0,18 | 0,12–0,20 |
| P4 | –DU | WU20PH | WU20PH | 90 | 150 | 220 | mm/rev | – | – | 0.08–0.13 | 0.09–0.15 |
| P5 | –V36 | WU40PH | WU25CH | 120 | 180 | 250 | mm/rev | 0,06–0,10 | 0,08–0,14 | 0,10–0,15 | 0,11–0,16 |
| P5 | –DU | WU20PH | WU20PH | 90 | 150 | 220 | mm/rev | – | – | 0.07–0.11 | 0.08–0.12 |
| P6 | -V36 | WU40PH | WU25CH | 120 | 160 | 210 | mm/rev | 0,06–0,10 | 0,08–0,14 | 0,10–0,15 | 0,11–0,16 |
| P6 | –DU | WU20PH | WU20PH | 90 | 130 | 165 | mm/rev | – | – | 0.07–0.11 | 0.08–0.12 |
| M1 | -V38 | WU40PH | WU40PH | 120 | 160 | 240 | mm/rev | 0,06–0,11 | 0,07–0,11 | 0,08–0,12 | 0,10–0,14 |
| M1 | –DU | WU20PH | WU20PH | 90 | 130 | 190 | mm/rev | – | – | 0.06–0.09 | 0.07–0.10 |
| M2 | –V38 | WU40PH | WU40PH | 110 | 140 | 210 | mm/rev | 0,06–0,10 | 0,07–0,11 | 0,08–0,12 | 0,10–0,14 |
| M2 | –DU | WU20PH | WU20PH | 110 | 140 | 190 | mm/rev | – | – | 0.06–0.09 | 0.07–0.10 |
| M3 | -V36 | WU40PH | WU40PH | 100 | 120 | 200 | mm/rev | 0,06–0,10 | 0,07–0,11 | 0,08–0,12 | 0,10–0,14 |
| M3 | –DU | WU20PH | WU20PH | 80 | 100 | 160 | mm/rev | – | – | 0.06–0.09 | 0.07–0.10 |
| K1 | -V34 | WU25CH | WPK10CH | 120 | 200 | 280 | mm/rev | 0,08–0,14 | 0,08–0,16 | 0,10–0,18 | 0,12–0,24 |
| K1 | –DU | WU20PH | WU20PH | 90 | 160 | 220 | mm/rev | – | – | 0.07–0.13 | 0.09–0.18 |
| K2 | –V34 | WU40PH | WPK10CH | 100 | 180 | 260 | mm/rev | 0,08–0,14 | 0,08–0,16 | 0,10–0,18 | 0,12–0,24 |
| K2 | –DU | WU20PH | WU20PH | 80 | 140 | 200 | mm/rev | – | – | 0.07–0.13 | 0.09–0.18 |
| K3 | -V34 | WU40PH | WPK10CH | 100 | 170 | 240 | mm/rev | 0,08–0,14 | 0,08–0,16 | 0,10–0,18 | 0,12–0,24 |
| K3 | –DU | WU20PH | WU20PH | 80 | 140 | 190 | mm/rev | – | – | 0.07–0.13 | 0.09–0.18 |
| N1 | -V36 | WN10PH | WN10PH | 250 | 350 | 500 | mm/rev | 0,06–0,10 | 0,08–0,14 | 0,10–0,15 | 0,11–0,16 |
| N2 | –V36 | WN10PH | WN10PH | 150 | 300 | 450 | mm/rev | 0,06–0,10 | 0,08–0,14 | 0,10–0,15 | 0,11–0,16 |
| N3 | -V36 | WN10PH | WN10PH | 80 | 120 | 150 | mm/rev | 0,06–0,10 | 0,07–0,11 | 0,08–0,12 | 0,10–0,14 |
| S3 | -V38 | WU40PH | WU40PH | 20 | 30 | 45 | mm/rev | 0,08–0,12 | 0,08–0,13 | 0,10–0,15 | 0,12–0,19 |
| S3 | –DU | WU20PH | WU20PH | 20 | 30 | 40 | mm/rev | – | – | 0.07–0.11 | 0.09–0.14 |
| S4 | –V38 | WU40PH | WU40PH | 35 | 40 | 65 | mm/rev | 0,08–0,12 | 0,08–0,13 | 0,10 –0,15 | 0,12–0,19 |
| S4 | –DU | WU20PH | WU20PH | 30 | 40 | 60 | mm/rev | – | – | 0.07–0.11 | 0.09–0.14 |
| Insert size | Diameter range mm (in) | 2 x D/3 x D | 4 x D | 5 x D | ||||||
| X-offset value max. in mm (max. in inch) | D1 max value mm (in) | Hole tolerance mm (in) | X-offset value max. in mm (max. in inch) | D1 max value mm (in) | Hole tolerance mm (in) | X-offset value max. in mm (max. in inch) | D1 max value mm (in) | Hole tolerance mm (in) | ||
| A | 12,00
|
0,5
|
D1 + 1mm
|
+/- 0,20
|
0,5
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| B | 14,00
|
0,5
|
D1 + 1mm
|
+/- 0,20
|
0,5
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| C | 19,00
|
0,5
|
D1 + 1mm
|
+/- 0,20
|
0,5
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| D | 24,00
|
0,8
|
D1 + 1,6mm
|
+/- 0,20
|
0,8
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| E | 30,00
|
0,8
|
D1 + 1,6mm
|
+/- 0,20
|
0,8
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| F | 37,00
|
0,8
|
D1 + 1,6mm
|
+/- 0,25
|
0,8
|
D1 + 1mm
|
+/- 0,38
|
|
|
+/- 0,38
|
| G | 46,00
|
1
|
D1 + 2mm
|
+/- 0,25
|
0,8
|
D1 + 1mm
|
+/- 0,38
|
|
|
+/- 0,38
|
| H | 57,00
|
1
|
D1 + 2mm
|
+/- 0,28
|
0,8
|
D1 + 1mm
|
+/- 0,42
|
|
|
+/- 0,42
|
| Insert size | Diameter Range (mm) | 2 x D and 3 x D | 4 x D | 5 x D | |||
| X-offset value
|
D1 max
|
X-offset value
|
D1 max
|
X-offset
|
D1 max
|
||
| A | 12,00
|
0,5 | D1 + 1mm | 0,5 | D1 + 1mm |
|
|
| B | 14,00
|
0,5 | D1 + 1mm | 0,5 | D1 + 1mm |
|
|
| C | 19,00
|
0,5 | D1 + 1mm | 0,5 | D1 + 1mm |
|
|
| D | 24,00
|
0,8 | D1 + 1,6mm | 0,8 | D1 + 1mm |
|
|
| E | 30,00
|
0,8 | D1 + 1,6mm | 0,8 | D1 + 1mm |
|
|
| F | 37,00
|
0,8 | D1 + 1,6mm | 0,8 | D1 + 1mm |
|
|
| G | 46,00
|
1 | D1 + 2mm | 0,8 | D1 + 1mm |
|
|
| H | 57,00
|
1 | D1 + 2mm | 0,8 | D1 + 1mm |
|
|
| Insert size | Diameter range mm (in) | 2 x D/3 x D | 4 x D | 5 x D | |||||
| D1 max value mm (in) | Hole tolerance mm (in) | X-offset value max. in mm (max. in inch) | D1 max value mm (in) | Hole tolerance mm (in) | X-offset value max. in mm (max. in inch) | D1 max value mm (in) | Hole tolerance mm (in) | ||
| A | 12,00
|
D1 + 1mm
|
+/- 0,20
|
0,5
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| B | 14,00
|
D1 + 1mm
|
+/- 0,20
|
0,5
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| C | 19,00
|
D1 + 1mm
|
+/- 0,20
|
0,5
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| D | 24,00
|
D1 + 1,6mm
|
+/- 0,20
|
0,8
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| E | 30,00
|
D1 + 1,6mm
|
+/- 0,20
|
0,8
|
D1 + 1mm
|
+/- 0,35
|
|
|
+/- 0,35
|
| F | 37,00
|
D1 + 1,6mm
|
+/- 0,25
|
0,8
|
D1 + 1mm
|
+/- 0,38
|
|
|
+/- 0,38
|
| G | 46,00
|
D1 + 2mm
|
+/- 0,25
|
0,8
|
D1 + 1mm
|
+/- 0,38
|
|
|
+/- 0,38
|
| H | 57,00
|
D1 + 2mm
|
+/- 0,28
|
0,8
|
D1 + 1mm
|
+/- 0,42
|
|
|
+/- 0,42
|
| Material
|
Geometry | Grade | Cutting Speed
|
Tool
|
1.188
|
1.469
|
1.813
|
2.250
|
|||
| center | periphery | Min | Start | Max | |||||||
| P0 | –V38 | WU40PH | WU25CH | 360 | 540 | 780 | IPR | 0.0051–0.0063 | 0.0059–0.0071 | 0.0063–0.0091 | 0.0067–0.0094 |
| – DU | WU20PH | WU20PH | 290 | 430 | 624 | IPR | 0.0040–0.0050 | 0.0047–0.0057 | – | – | |
| P1 | –V38 | WU40PH | WU25CH | 360 | 540 | 780 | IPR | 0.0051–0.0071 | 0.0059–0.0079 | 0.0063–0.0106 | 0.0067–0.0114 |
| – DU | WU20PH | WU20PH | 290 | 430 | 625 | IPR | 0.0040–0.0057 | 0.0047–0.0063 | – | – | |
| P2 | –V34 | WU40PH | WU25CH | 360 | 570 | 840 | IPR | 0.0051–0.0079 | 0.0059–0.0083 | 0.0063–0.0110 | 0.0067–0.0118 |
| – DU | WU20PH | WU20PH | 290 | 450 | 675 | IPR | 0.0040–0.0063 | 0.0047–0.0063 | – | – | |
| P3 | –V34 | WU40PH | WPK10CH | 360 | 600 | 930 | IPR | 0.0053–0.0094 | 0.0063–0.0094 | 0.0071–0.0118 | 0.0075–0.0126 |
| – DU | WU20PH | WU20PH | 290 | 480 | 745 | IPR | 0.0042–0.0075 | 0.0050–0.0075 | – | – | |
| P4 | –V34 | WU40PH | WPK10CH | 360 | 570 | 930 | IPR | 0.0055–0.0087 | 0.0063–0.0094 | 0.0071–0.0118 | 0.0075–0.0126 |
| – DU | WU20PH | WU20PH | 290 | 450 | 745 | IPR | 0.0044–0.0069 | 0.0050–0.0075 | – | – | |
| P5 | –V36 | WU40PH | WU25CH | 360 | 540 | 750 | IPR | 0.0051–0.0071 | 0.0059–0.0079 | 0.0063–0.0110 | 0.0067–0.0118 |
| – DU | WU20PH | WU20PH | 290 | 430 | 600 | IPR | 0.0040–0.0057 | 0.0047–0.0063 | – | – | |
| P6 | -V36 | WU40PH | WU25CH | 360 | 480 | 630 | IPR | 0.0051–0.0071 | 0.0059–0.0079 | 0.0063–0.0110 | 0.0067–0.0114 |
| - DU | WU20PH | WU20PH | 290 | 380 | 500 | IPR | 0.0040-0.0057 | 0.0047-0.0063 | - | - | |
| M1 | -V38 | WU40PH | WU40PH | 360 | 480 | 720 | IPR | 0.0047–0.0079 | 0.0055–0.0098 | 0.0063–0.0110 | 0.0063–0.0118 |
| - DU | WU20PH | WU20PH | 290 | 385 | 575 | IPR | 0.0038-0.0063 | 0.0044-0.0078 | - | - | |
| M2 | –V38 | WU40PH | WU40PH | 330 | 420 | 630 | IPR | 0.0047–0.0079 | 0.0055–0.0098 | 0.0063–0.0110 | 0.0063–0.0118 |
| – DU | WU20PH | WU20PH | 265 | 330 | 500 | IPR | 0.0038–0.0063 | 0.0044–0.0078 | – | – | |
| M3 | -V36 | WU40PH | WU40PH | 300 | 360 | 600 | IPR | 0.0047–0.0079 | 0.0055–0.0098 | 0.0063–0.0110 | 0.0063–0.0118 |
| - DU | WU20PH | WU20PH | 240 | 290 | 480 | IPR | 0.0038-0.0063 | 0.0044-0.0098 | - | - | |
| K1 | -V34 | WU25CH | WPK10CH | 360 | 600 | 840 | IPR | 0.0055–0.0102 | 0.0063–0.0118 | 0.0071–0.0126 | 0.0079–0.0142 |
| - DU | WU20PH | WU20PH | 290 | 480 | 670 | IPR | 0.0044-0.0081 | 0.0050-0.0094 | - | - | |
| K2 | –V34 | WU40PH | WPK10CH | 300 | 540 | 780 | IPR | 0.0055–0.0102 | 0.0063–0.0118 | 0.0071–0.0126 | 0.0079–0.0142 |
| – DU | WU20PH | WU20PH | 240 | 430 | 625 | IPR | 0.0044–0.0081 | 0.0050–0.0094 | – | – | |
| K3 | -V34 | WU40PH | WPK10CH | 300 | 510 | 720 | IPR | 0.0055–0.0102 | 0.0063–0.0118 | 0.0071–0.0126 | 0.0079–0.0142 |
| - DU | WU20PH | WU20PH | 240 | 400 | 575 | IPR | 0.0044-0.0081 | 0.0050-0.0094 | - | - | |
| N1 | -V36 | WN10PH | WN10PH | 750 | 1050 | 1500 | IPR | 0.0051–0.0071 | 0.0059–0.0079 | 0.0063–0.0110 | 0.0067–0.0118 |
| N2 | –V36 | WN10PH | WN10PH | 450 | 900 | 1350 | IPR | 0.0051–0.0071 | 0.0059–0.0079 | 0.0063–0.0110 | 0.0067–0.0118 |
| N3 | -V36 | WN10PH | WN10PH | 240 | 360 | 450 | IPR | 0.0047–0.0067 | 0.0055–0.0083 | 0.0063–0.0091 | 0.0063–0.0094 |
| S3 | -V38 | WU40PH | WU40PH | 60 | 90 | 135 | IPR | 0.0055–0.0083 | 0.0063–0.0094 | 0.0071–0.0102 | 0.0079–0.0118 |
| - DU | WU20PH | WU20PH | 50 | 70 | 100 | IPR | 0.0044-0.083 | 0.0050-0.0075 | - | - | |
| S4 | –V38 | WU40PH | WU40PH | 105 | 120 | 195 | IPR | 0.0055–0.0083 | 0.0063–0.0094 | 0.0071–0.0102 | 0.0079–0.0118 |
| – DU | WU20PH | WU20PH | 85 | 95 | 150 | IPR | 0.0044–0.0664 | 0.0050–0.0075 | – | – | |
| Recommended Feed Rate per Revolution | |||||||||||
| Material
|
Geometry | Grade | Cutting Speed
|
Tool
|
.473
|
.563
|
.750
|
.969
|
|||
| center | periphery | Min | Start | Max | |||||||
| P0 | –V38 | WU40PH | WU25CH | 360 | 540 | 780 | IPR | 0.0024–0.0031 | 0.0031–0.0043 | 0.0039–0.0051 | 0.0043–0.0055 |
| – DU | WU20PH | WU20PH | 290 | 430 | 625 | IPR | – | – | 0.0031–0.0041 | 0.0034–0.0044 | |
| P1 | –V38 | WU40PH | WU25CH | 360 | 540 | 780 | IPR | 0.0024–0.0039 | 0.0031–0.0051 | 0.0039–0.0059 | 0.0043–0.0063 |
| – DU | WU20PH | WU20PH | 290 | 430 | 625 | IPR | – | – | 0.0031–0.0047 | 0.0034–0.0050 | |
| P2 | –V34 | WU40PH | WU25CH | 360 | 570 | 840 | IPR | 0.0024–0.0039 | 0.0031–0.0059 | 0.0039–0.0063 | 0.0043–0.0067 |
| – DU | WU20PH | WU20PH | 290 | 450 | 675 | IPR | – | – | 0.0031–0.0050 | 0.0034–0.0054 | |
| P3 | –V34 | WU40PH | WPK10CH | 360 | 600 | 930 | IPR | 0.0031–0.0059 | 0.0039–0.0063 | 0.0043–0.0071 | 0.0047–0.0079 |
| – DU | WU20PH | WU20PH | 290 | 480 | 745 | IPR | – | – | 0.0034–0.0067 | 0.0037–0.0063 | |
| P4 | –V34 | WU40PH | WPK10CH | 360 | 570 | 930 | IPR | 0.0031–0.0059 | 0.0039–0.0063 | 0.0043–0.0071 | 0.0047–0.0079 |
| – DU | WU20PH | WU20PH | 290 | 450 | 745 | IPR | – | – | 0.0034–0.0067 | 0.0037–0.0063 | |
| P5 | –V36 | WU40PH | WU25CH | 360 | 540 | 750 | IPR | 0.0024–0.0039 | 0.0031–0.0055 | 0.0039–0.0059 | 0.0043–0.0063 |
| – DU | WU20PH | WU20PH | 290 | 430 | 600 | IPR | – | – | 0.0031–0.0047 | 0.0034–0.0050 | |
| P6 | -V36 | WU40PH | WU25CH | 360 | 480 | 630 | IPR | 0.0024–0.0039 | 0.0031–0.0055 | 0.0039–0.0059 | 0.0043–0.0063 |
| -V36 | WU40PH | WU25CH | 290 | 385 | 500 | IPR | - | - | 0.0031-0.0047 | 0.0034-0.0050 | |
| M1 | -V38 | WU40PH | WU40PH | 360 | 480 | 720 | IPR | 0.0024–0.0047 | 0.0028–0.0051 | 0.0031–0.0059 | 0.0039–0.0063 |
| - DU | WU20PH | WU20PH | 290 | 385 | 575 | IPR | - | - | 0.0025-0.0047 | 0.0031-0.0050 | |
| M2 | –V38 | WU40PH | WU40PH | 330 | 420 | 630 | IPR | 0.0024–0.0047 | 0.0028–0.0051 | 0.0031–0.0059 | 0.0039–0.0063 |
| – DU | WU20PH | WU20PH | 265 | 340 | 500 | IPR | – | – | 0.0025–0.0047 | 0.0031–0.0050 | |
| M3 | -V36 | WU40PH | WU40PH | 300 | 360 | 600 | IPR | 0.0024–0.0047 | 0.0028–0.0051 | 0.0031–0.0059 | 0.0039–0.0063 |
| - DU | WU20PH | WU20PH | 240 | 290 | 480 | IPR | - | - | 0.0025-0.0047 | 0.0031-0.0050 | |
| K1 | -V34 | WU25CH | WPK10CH | 360 | 600 | 840 | IPR | 0.0031–0.0055 | 0.0031–0.0063 | 0.0039–0.0071 | 0.0047–0.0094 |
| - DU | WU20PH | WU20PH | 290 | 480 | 675 | IPR | - | - | 0.0031-0.0057 | 0.0038-0.0075 | |
| K2 | –V34 | WU40PH | WPK10CH | 300 | 540 | 780 | IPR | 0.0031–0.0055 | 0.0031–0.0063 | 0.0039–0.0071 | 0.0047–0.0094 |
| – DU | WU20PH | WU20PH | 240 | 430 | 625 | IPR | – | – | 0.0031–0.0057 | 0.0038–0.0075 | |
| K3 | -V34 | WU40PH | WPK10CH | 300 | 510 | 720 | IPR | 0.0031–0.0055 | 0.0031–0.0063 | 0.0039–0.0071 | 0.0047–0.0094 |
| - DU | WU20PH | WU20PH | 240 | 400 | 575 | IPR | - | - | 0.0031-0.0057 | 0.0038-0.0075 | |
| N1 | -V36 | WN10PH | WN10PH | 750 | 1050 | 1500 | IPR | 0.0024–0.0039 | 0.0031–0.0055 | 0.0039–0.0059 | 0.0043–0.0063 |
| N2 | –V36 | WN10PH | WN10PH | 450 | 900 | 1350 | IPR | 0.0024–0.0039 | 0.0031–0.0055 | 0.0039–0.0059 | 0.0043–0.0063 |
| N3 | -V36 | WN10PH | WN10PH | 240 | 360 | 450 | IPR | 0.0024–0.0039 | 0.0028–0.0043 | 0.0031–0.0047 | 0.0039–0.0055 |
| S3 | -V38 | WU40PH | WU40PH | 60 | 90 | 135 | IPR | 0.0031–0.0047 | 0.0031–0.0051 | 0.0039–0.0059 | 0.0047–0.0075 |
| - DU | WU20PH | WU20PH | 50 | 70 | 100 | IPR | - | - | 0.0031-0.0047 | 0.0038-0.006 | |
| S4 | –V38 | WU40PH | WU40PH | 105 | 120 | 195 | IPR | 0.0031–0.0047 | 0.0031–0.0051 | 0.0039–0.0059 | 0.0047–0.0075 |
| – DU | WU20PH | WU20PH | 85 | 95 | 150 | IPR | – | – | 0.0031–0.0047 | 0.0038–0.006 | |
| Recommended Feed Rate per Revolution | |||||||||||
| Material
|
Geometry | Grade | Cutting Speed
|
Tool
|
.473
|
.563
|
.750
|
.969
|
|||
| center | periphery | Min | Start | Max | |||||||
| P0 | –V38 | WU40PH | WU25CH | 360 | 540 | 780 | IPR | 0.0024–0.0031 | 0.0031–0.0043 | 0.0039–0.0051 | 0.0043–0.0055 |
| – DU | WU20PH | WU20PH | 290 | 430 | 625 | IPR | – | – | 0.0031–0.0041 | 0.0034–0.0044 | |
| P1 | –V38 | WU40PH | WU25CH | 360 | 540 | 780 | IPR | 0.0024–0.0039 | 0.0031–0.0051 | 0.0039–0.0059 | 0.0043–0.0063 |
| – DU | WU20PH | WU20PH | 290 | 430 | 625 | IPR | – | – | 0.0031–0.0047 | 0.0034–0.0050 | |
| P2 | –V34 | WU40PH | WU25CH | 360 | 570 | 840 | IPR | 0.0024–0.0039 | 0.0031–0.0059 | 0.0039–0.0063 | 0.0043–0.0067 |
| – DU | WU20PH | WU20PH | 290 | 450 | 675 | IPR | – | – | 0.0031–0.0050 | 0.0034–0.0054 | |
| P3 | –V34 | WU40PH | WPK10CH | 360 | 600 | 930 | IPR | 0.0031–0.0059 | 0.0039–0.0063 | 0.0043–0.0071 | 0.0047–0.0079 |
| – DU | WU20PH | WU20PH | 290 | 480 | 745 | IPR | – | – | 0.0034–0.0067 | 0.0037–0.0063 | |
| P4 | –V34 | WU40PH | WPK10CH | 360 | 570 | 930 | IPR | 0.0031–0.0059 | 0.0039–0.0063 | 0.0043–0.0071 | 0.0047–0.0079 |
| – DU | WU20PH | WU20PH | 290 | 450 | 745 | IPR | – | – | 0.0034–0.0067 | 0.0037–0.0063 | |
| P5 | –V36 | WU40PH | WU25CH | 360 | 540 | 750 | IPR | 0.0024–0.0039 | 0.0031–0.0055 | 0.0039–0.0059 | 0.0043–0.0063 |
| – DU | WU20PH | WU20PH | 290 | 430 | 600 | IPR | – | – | 0.0031–0.0047 | 0.0034–0.0050 | |
| P6 | -V36 | WU40PH | WU25CH | 360 | 480 | 630 | IPR | 0.0024–0.0039 | 0.0031–0.0055 | 0.0039–0.0059 | 0.0043–0.0063 |
| -V36 | WU40PH | WU25CH | 290 | 385 | 500 | IPR | - | - | 0.0031-0.0047 | 0.0034-0.0050 | |
| M1 | -V38 | WU40PH | WU40PH | 360 | 480 | 720 | IPR | 0.0024–0.0047 | 0.0028–0.0051 | 0.0031–0.0059 | 0.0039–0.0063 |
| - DU | WU20PH | WU20PH | 290 | 385 | 575 | IPR | - | - | 0.0025-0.0047 | 0.0031-0.0050 | |
| M2 | –V38 | WU40PH | WU40PH | 330 | 420 | 630 | IPR | 0.0024–0.0047 | 0.0028–0.0051 | 0.0031–0.0059 | 0.0039–0.0063 |
| – DU | WU20PH | WU20PH | 265 | 340 | 500 | IPR | – | – | 0.0025–0.0047 | 0.0031–0.0050 | |
| M3 | -V36 | WU40PH | WU40PH | 300 | 360 | 600 | IPR | 0.0024–0.0047 | 0.0028–0.0051 | 0.0031–0.0059 | 0.0039–0.0063 |
| - DU | WU20PH | WU20PH | 240 | 290 | 480 | IPR | - | - | 0.0025-0.0047 | 0.0031-0.0050 | |
| K1 | -V34 | WU25CH | WPK10CH | 360 | 600 | 840 | IPR | 0.0031–0.0055 | 0.0031–0.0063 | 0.0039–0.0071 | 0.0047–0.0094 |
| - DU | WU20PH | WU20PH | 290 | 480 | 675 | IPR | - | - | 0.0031-0.0057 | 0.0038-0.0075 | |
| K2 | –V34 | WU40PH | WPK10CH | 300 | 540 | 780 | IPR | 0.0031–0.0055 | 0.0031–0.0063 | 0.0039–0.0071 | 0.0047–0.0094 |
| – DU | WU20PH | WU20PH | 240 | 430 | 625 | IPR | – | – | 0.0031–0.0057 | 0.0038–0.0075 | |
| K3 | -V34 | WU40PH | WPK10CH | 300 | 510 | 720 | IPR | 0.0031–0.0055 | 0.0031–0.0063 | 0.0039–0.0071 | 0.0047–0.0094 |
| - DU | WU20PH | WU20PH | 240 | 400 | 575 | IPR | - | - | 0.0031-0.0057 | 0.0038-0.0075 | |
| N1 | -V36 | WN10PH | WN10PH | 750 | 1050 | 1500 | IPR | 0.0024–0.0039 | 0.0031–0.0055 | 0.0039–0.0059 | 0.0043–0.0063 |
| N2 | –V36 | WN10PH | WN10PH | 450 | 900 | 1350 | IPR | 0.0024–0.0039 | 0.0031–0.0055 | 0.0039–0.0059 | 0.0043–0.0063 |
| N3 | -V36 | WN10PH | WN10PH | 240 | 360 | 450 | IPR | 0.0024–0.0039 | 0.0028–0.0043 | 0.0031–0.0047 | 0.0039–0.0055 |
| S3 | -V38 | WU40PH | WU40PH | 60 | 90 | 135 | IPR | 0.0031–0.0047 | 0.0031–0.0051 | 0.0039–0.0059 | 0.0047–0.0075 |
| - DU | WU20PH | WU20PH | 50 | 70 | 100 | IPR | - | - | 0.0031-0.0047 | 0.0038-0.006 | |
| S4 | –V38 | WU40PH | WU40PH | 105 | 120 | 195 | IPR | 0.0031–0.0047 | 0.0031–0.0051 | 0.0039–0.0059 | 0.0047–0.0075 |
| – DU | WU20PH | WU20PH | 85 | 95 | 150 | IPR | – | – | 0.0031–0.0047 | 0.0038–0.006 | |
Verkauft in Pkg. von
Verkauft in Pkg. von
ISO Katalog
ANSI Katalog
to find similar products.Please select a file to download
Models
Product data
I have read and accepted the Terms & Conditions of use
Can’t find the file type you’re looking for?
. Please enter the desired qty for the material(s) you want to include in your promotion or Proceed Without Promotion and only your base materials will be added to the cart.
Minimum quantity should be
| SAP Material Number | ISO Katalog | Grade |
|---|
Thank you for your registration, pending approval & completion of the registration, your access is currently limited. Full utilization of product search capabilities & collaboration space is available and will remain. Please allow 2 business days for registration completion.
Vielen Dank für Ihre erfolgreiche Registrierung. Sie können sich nun sofort einloggen und die Website nutzen.
You are about to leave the Solution building process.
Are you sure you want to leave?
